- 您現在的位置：買賣IC網 > PDF目錄69018 > MAX8893BEWV+ (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY MICROPROCESSOR CIRCUIT, PBGA30 PDF資料下載
參數資料
| 型號： | MAX8893BEWV+ |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | SPECIALTY MICROPROCESSOR CIRCUIT, PBGA30 |
| 封裝： | 3 X 2.50 MM, 0.64 MM HEIGHT, ROHS COMPLIANT, WLP-30 |
| 文件頁數： | 25/51頁 |
| 文件大小： | 4976K |
| 代理商： | MAX8893BEWV+ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁
PMICs for Multimedia Application Processors
in a 3.0mm x 2.5mm WLP
MAX8893A/MAX8893B/MAX8893C
______________________________________________________________________________________ 31
Analog Signal Levels
The on-resistance of the USB switch is very low and
stable as the analog input signals are swept from ground
to VIN (see the Typical Operating Characteristics). These
switches are bidirectional, allowing NO_, NC_, and
COM_ to be configured as either inputs or outputs. The
charge-pump-assisted n-channel architecture allows the
switch to pass analog signals that exceed VIN up to the
overvoltage fault protection threshold. This allows USB
signals that exceed VIN to pass, allowing compliance
with USB requirements for voltage levels.
Overvoltage Fault Protection
The USB switch features overvoltage fault protection
on COM_. Fault protection protects the switch and USB
transceiver from damaging voltage levels. When volt-
ages on COM_ exceed the fault protection threshold
(VFP), COM_, NC_, and NO_ are high impedance.
Enable Input (ENUSB)
The USB switch features a shutdown mode that reduces
the quiescent current supply and places COM_ in high
impedance. Drive ENUSB high to place the USB switch
in shutdown mode. Drive ENUSB low to allow the USB
switch to enter normal operation.
Load Switch
The MAX8893A/MAX8893B/MAX8893C include an ultra-
low RON p-channel MOSFET load switch. The switch
has its own enable input, ENLS. When it is enabled, its
output soft-starts with I2C programmed rising time to
avoid inrush current. See Table 8. The switch input is
from the step-down converter output and can operate
over the 0.8V to 2.4V range. With LS_ADEN bit set to 1,
when the switch is disabled, an internal 100ω resistor is
connected between the load switch output and ground
for quick discharging.
I2C Serial Interface
An I2C-compatible, 2-wire serial interface controls all the
regulator output voltages, load switch timing, individual
enable/disable control, and other parameters. The serial
bus consists of a bidirectional serial-data line (SDA) and
a serial-clock input (SCL). The MAX8893A/MAX8893B/
MAX8893C are slave-only devices, relying upon a
master to generate a clock signal. The master initiates
data transfer to and from the MAX8893A/MAX8893B/
MAX8893C and generates SCL to synchronize the data
transfer (Figure 8).
I2C is an open-drain bus. Both SDA and SCL are bidi-
rectional lines, connected to a positive supply voltage
through a pullup resistor. They both have Schmitt trig-
gers and filter circuits to suppress noise spikes on the
bus to assure proper device operation.
Figure 8. 2-Wire Serial Interface Timing Detail
SCL
SDA
tR
tF
tBUF
START
CONDITION
STOP
CONDITION
REPEATED START CONDITION
START CONDITION
tSU,STO
tHD,STA
tSU,STA
tHD,DAT
tSU,DAT
tLOW
tHIGH
tHD,STA
相關PDF資料 |
PDF描述 |
|---|---|
| MAX8893CEWV+ | SPECIALTY MICROPROCESSOR CIRCUIT, PBGA30 |
| MAX9485ETP+ | 73.728 MHz, OTHER CLOCK GENERATOR, QCC20 |
| MAXQ1004-B01+ | RISC MICROCONTROLLER, QCC16 |
| MAXQ2010-RFX+ | 16-BIT, FLASH, 10 MHz, RISC MICROCONTROLLER, PQFP100 |
| MAXQ3120-FFN+ | 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PQFP80 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX8893BEWV+T | 制造商:Maxim Integrated Products 功能描述:UPMIC FOR APPLICATION PROCESSOR - Tape and Reel |
| MAX8893CEWV+ | 制造商:Maxim Integrated Products 功能描述:UPMIC FOR APPLICATION PROCESSOR - Rail/Tube |
| MAX8893CEWV+T | 制造商:Maxim Integrated Products 功能描述:UPMIC FOR APPLICATION PROCESSOR - Tape and Reel |
| MAX8895EVKIT+ | 功能描述:電池管理 EVKIT for MAX8895 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| MAX8895VEWA+ | 制造商:Maxim Integrated Products 功能描述:LI-ION CHARGERS WITH SMART POWER SELECTOR, ADAPTER TYPE DETE - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。