參數資料
型號: MAX9611AUB+T
廠商: Maxim Integrated Products
文件頁數: 5/20頁
文件大?。?/td> 0K
描述: IC 12BIT ADC OPAMP COMPAR 10UMAX
標準包裝: 2,500
放大器類型: 電流檢測
電路數: 1
增益帶寬積: 2.5MHz
-3db帶寬: 4MHz
電流 - 輸入偏壓: 1µA
電壓 - 輸入偏移: 100µV
電流 - 電源: 1.6mA
電流 - 輸出 / 通道: 15mA
電壓 - 電源,單路/雙路(±): 2.7 V ~ 5.5 V
工作溫度: -40°C ~ 125°C
安裝類型: *
封裝/外殼: *
供應商設備封裝: *
包裝: *
High-Side, Current-Sense Amplifiers with
12-Bit ADC and Op Amp/Comparator
MAX9611/MAX9612
______________________________________________________________________________________ 13
SET Voltage Measurement
The SET voltage serves as a reference voltage for the
internal op amp or comparator around which a control
loop can be designed. The low bias current for SET
allows high-impedance resistor-dividers and current-
output DACs to be used, making it easy to interface
without introducing additional errors.
The SET input can also serve as an auxiliary input port
to the ADC, if the op amp or comparator is not utilized
in the application. Its full-scale input range extends from
0V to 1.10V.
OUT Voltage Measurement
The internal amplifier/comparator output voltage can be
monitored over the entire 0V to 57.3V range by the ADC.
An internal high-value resistor divider on OUT reduces
leakage current effects.
Common-Mode Voltage Measurement
The input common-mode voltage is defined as the aver-
age of the voltage at RS+ and RS-. A high value resistor-
divider allows measurement of the input common-mode
voltage over the 0V to 57.3V range.
Sense Voltage Measurement
Three programmable gains allow for a wide range of cur-
rents to be read by the ADC. The current-sense amplifier
gain can be set to 1x, 4x, or 8x. The full-scale sense volt-
ages are then 440mV, 110mV, and 55mV, respectively.
Output Amplifier/Comparator
The MAX9611/MAX9612 feature an internally selectable
op amp and comparator where one of the inputs is con-
nected to the 2.5x current-sense amplifier, and the other
input is connected to the SET input. The op amp or the
comparator output can be selected and connected to
OUT. The output stage is an open-drain 60V nFET, that
requires a suitable pullup resistor for proper opera-
tion. The op amp then behaves like a Class-A output
stage. Select op amp or comparator function in Control
Register 1 (0x0A) bit 7 (see Tables 4 and 5).
Watchdog/Latch/Retry Functionality
Internal digital circuitry is used to implement a watchdog
feature that can be useful to handle normal application
transients that are not true fault conditions. This feature
applies both to the op amp and comparator modes of
part operation. A watchdog delay time is internally set to
1ms by default but can be changed to 100Fs. The retry
delay time is internally set to 50ms by default, but can be
changed to 10ms (see Tables 6 and 7).
In normal operation mode, (Control Register 1 (0x0A)
000x xxxx), the amplifier output responds to the differ-
ence between its inputs, i.e., the CSA output voltage and
the SET voltage. In open-loop configuration, the op amp
can be used as a comparator.
In a watchdog-latch-retry mode (Control Register 1
(0x0A) 111x xxxx), the output of the comparator waits
for a watchdog delay time (to ensure the CSA output
continues to stay above the SET voltage for this duration)
before responding, and then latches onto this state. After
a retry delay time, it resets the comparator state and the
cycle repeats.
Similar functionality is implemented for the op-amp
mode as well (Control Register 1 (0x0A) 000x xxxx to
011x xxxx).
A RESET bit is defined in Control Register 1 (0x0A) to
reset a latched state when commanded by the user.
I2C Interface
The MAX9611/MAX9612 I2C interface consists of a
serial-data line (SDA) and serial-clock line (SCL). SDA
and SCL facilitate bidirectional communication between
the MAX9611/MAX9612 and the master at rates up to
400kHz. The MAX9611/MAX9612 are slave devices that
transfer and receive data. The master (typically a micro-
controller) initiates data transfer on the bus and gener-
ates the SCL signal to permit that transfer.
相關PDF資料
PDF描述
MAX9614AXT+T IC OPAMP GP RR 2.8MHZ LP SC70-6
MAX9615AXA+T IC OPAMP RRIO 2.8MHZ DUAL SC70-8
MAX9619AXT+T IC OP AMP RRIO LOW POWER SC70-6
MAX9623AXK+T IC OPAMP RAIL-TO-RAIL SC70-5
MAX9627ATC+ IC DIFF AMP/DRIVER LN 12TQFN
相關代理商/技術參數
參數描述
MAX9611EVKIT+ 功能描述:放大器 IC 開發工具 MAX9611 Eval Kit RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V
MAX9611PMB1# 功能描述:放大器 IC 開發工具 MAX9611 Peripheral Module RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V
MAX9612AUB+ 功能描述:電流靈敏放大器 iSense + ADC + I2C RoHS:否 制造商:Texas Instruments 通道數量: 共模抑制比(最小值):110 dB 輸入補償電壓:80 uV 電源電壓-最大:5.5 V 電源電壓-最小:2.7 V 電源電流:350 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-16 封裝:Reel
MAX9612AUB+T 功能描述:電流靈敏放大器 iSense + ADC + I2C RoHS:否 制造商:Texas Instruments 通道數量: 共模抑制比(最小值):110 dB 輸入補償電壓:80 uV 電源電壓-最大:5.5 V 電源電壓-最小:2.7 V 電源電流:350 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-16 封裝:Reel
MAX9613AXT+ 制造商:Maxim Integrated Products 功能描述: 制造商:Maxim Integrated Products 功能描述:RAIL-RAIL PRECISION 3MHZ OP AMP - Rail/Tube