- 您現在的位置：買賣IC網 > PDF目錄1946 > MAX9921AUB/V+T (Maxim Integrated Products)IC HALL EFFECT SENSOR DL 10UMAX PDF資料下載
參數資料
| 型號： | MAX9921AUB/V+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 4/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC HALL EFFECT SENSOR DL 10UMAX |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 類型： | 霍爾效應傳感器 |
| 輸入類型： | 電壓 |
| 輸出類型： | 邏輯 |
| 接口： | 2 線 |
| 電流 - 電源： | 1.3mA |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-µMAX |
| 包裝： | 帶卷 (TR) |
MAX9921
Hall Input Short-to-Ground
The Hall input shorted-to-ground fault is effectively a
latched condition if the input remains loaded by the Hall
switch when the shorting condition is removed. The cur-
rent required to power the Hall switch is shut off and only
a 50A pullup current remains. The Hall input can be
manually re-energized or it can be re-energized by the
ECU. A falling edge at DIAG initiates a restart with a
blanking cycle of any Hall input that has been shut down
due to the shorted-to-ground condition. During startup or
restart, it is possible for a Hall input to charge up an exter-
nal capacitance of 0.02F without tripping into a shorted-
to-ground latched state. All other fault conditions are not
latched and when these other faults are removed, ERR
goes high and the Hall input is again functional.
Manual Method for Re-Energizing Hall Sensor
and Means for Diagnosing an Intermittent
Hall Sensor Connection
Figure 4 shows the behavior of the MAX9921 when a
Hall input is open. Figure 5 shows the behavior of the
MAX9921 when the open input is reconnected to a Hall
sensor. Figures 4 and 5 demonstrate how a shorted-to-
ground Hall input can be reset.
Resetting a shorted-to-ground Hall input involves
three steps:
1) Relieve the short to ground at the Hall sensor.
2) Disconnect the Hall input from the Hall sensor (open
input fault condition).
3) Reconnect the Hall input to the Hall sensor.
The MAX9921 restarts the Hall input with a blanking
cycle. If the Hall input is disconnected from the Hall
sensor for 10ms, it allows the Hall input to be pulled up
by the 50A pullup current to register the open-input
fault condition. Then, reconnecting the Hall input to the
Hall sensor restarts the Hall input with a blanking cycle.
This provides a manual means of re-energizing a Hall
input without having to resort to the ECU to reset it. This
also demonstrates that an intermittent connection to a
Hall sensor can recover without intervention of the ECU.
This gives the ECU a means of diagnosing an intermit-
tent connection to a Hall sensor by using the diagnostic
mode to detect a diagnostic sequence of “open-circuit”
to “blanking cycle” to “no fault.”
Dual, 2-Wire Hall-Effect Sensor Interface
with Diagnostics
12
______________________________________________________________________________________
14V
VIN_
IIN_
0V
HALL INPUT
SHORT TO
GROUND FAULT
INDICATED
HALL INPUT
OPEN-CIRCUIT
FAULT INDICATED
TIME
VBAT - 25mV
5mV/ms
TIME
50
A
0A
HALL INPUT
DISCONNECTED
FROM SENSOR
Figure 4. Hall Input Ramps to Open-Circuit Fault When Short to Ground is Relieved
相關PDF資料 |
PDF描述 |
|---|---|
| MAX9925AUB+ | IC SENSOR INTERFACE VARI 10MSOP |
| MAX9950DCCB+TD | IC PMU DUAL 64TQFP |
| MAX9952FCCB+T | IC PMU DUAL 64TQFP |
| MAXQ2000-RAX+ | IC MCU 32K FLASH 68-QFN |
| MAXQ2010-RFX+ | IC MCU 16BIT 64KB FLASH 100-LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9921EVKIT+ | 功能描述:界面開發工具 MAX9921 Eval Kit RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| MAX9922ABT+T | 制造商:Maxim Integrated Products 功能描述:ULTRA-PRECISION, HIGH-SIDE CURRENT-SENSE AMPLIFIERS - Tape and Reel |
| MAX9922AUB+ | 功能描述:電流靈敏放大器 Current-Sense Amplifier RoHS:否 制造商:Texas Instruments 通道數量: 共模抑制比（最小值）:110 dB 輸入補償電壓:80 uV 電源電壓-最大:5.5 V 電源電壓-最小:2.7 V 電源電流:350 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-16 封裝:Reel |
| MAX9922AUB+T | 功能描述:電流靈敏放大器 Current-Sense Amplifier RoHS:否 制造商:Texas Instruments 通道數量: 共模抑制比（最小值）:110 dB 輸入補償電壓:80 uV 電源電壓-最大:5.5 V 電源電壓-最小:2.7 V 電源電流:350 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-16 封裝:Reel |
| MAX9922EUB+ | 功能描述:電流靈敏放大器 Current-Sense Amplifier RoHS:否 制造商:Texas Instruments 通道數量: 共模抑制比（最小值）:110 dB 輸入補償電壓:80 uV 電源電壓-最大:5.5 V 電源電壓-最小:2.7 V 電源電流:350 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。