- 您現在的位置：買賣IC網 > PDF目錄377894 > MB86606A (Fujitsu Limited) FAST-20 SCSI Protocol Controller PDF資料下載
參數資料
| 型號： | MB86606A |
| 廠商： | Fujitsu Limited |
| 英文描述： | FAST-20 SCSI Protocol Controller |
| 中文描述： | 快20的SCSI協議控制器 |
| 文件頁數： | 16/64頁 |
| 文件大?。?/td> | 605K |
| 代理商： | MB86606A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
16
MB86606A
I
BLOCK FUNCTIONS
1. Internal Processor
This processor provides the sequence control between each phase.
2. Timer
This timer manages the time specified by SCSI and the following time:
REQ/ACK assertion time for data at asynchronous transfer
Selection/reselection retry time
Selection/reselection timeout time
REQ/ACK timeout time during transfer
Asynchronous transfer (target)
: Time required for initiator to assert ACK signal after asserting REQ
signal
: Time required for target to negate REQ signal after asserting ACK
signal
: Time required for target to receive ACK signal for setting offset value
to 0 from initiator after sending REQ signal
Asynchronous transfer (initiator)
Synchronous transfer (target only)
3. Phase Controller
This controller controls the arbitration, selection/reselection, data-in/out, command, status, and message-in/out
phases executed on the SCSI bus.
4. Transfer Controller
This controller controls the information (data, command, status, message) transfer phases executed on the SCSI
bus.
There are two types of transfer for executing the information transfer phases.
Asynchronous transfer
Synchronous transfer
: Control by interlocking REQ and ACK signals
: Control with maximum of 32-byte offset value in data-in/out phase
Depending on the data migration, there are the following two modes.
Program transfer : Performed via MPU interface using data registers
DMA transfer
: Performed via DMA interface using DREQ and DACK pins
At synchronous transfer, the transfer parameters (transfer mode, minimum cycle period of REQ or ACK signal
sent from SPC in synchronous transfer, and maximum value between REQ and ACK signals in synchronous
transfer) can be saved for each ID and are automatically set when the data phase is started. The transfer byte
count is determined by block length
×
number of blocks.
5. Various Registers
Command register
This register specifies each command with an 8-bit code.
When using the user program, specify “1” at the Bit 7. The lower 7 bits (Bit 6 to Bit 0) are invalid.
Nexus status register
This register indicates the chip’s operating condition, the nexused partner’s ID, and data register status.
SCSI control signal status register
This register indicates the status of SCSI control signals.
相關PDF資料 |
PDF描述 |
|---|---|
| MB86606APMT2 | FAST-20 SCSI Protocol Controller |
| MB86606 | FAST-20 SCSI Protocol Controller(FAST-20 SCSI 協議控制器) |
| MB86612 | IEEE 1394 Bus Controller (for MPEG, DVC) |
| MB86612PBT | IEEE 1394 Bus Controller (for MPEG, DVC) |
| MB86612PFV | IEEE 1394 Bus Controller (for MPEG, DVC) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB86606APMT2 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:FAST-20 SCSI Protocol Controller |
| MB86612 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:IEEE 1394 Bus Controller (for MPEG, DVC) |
| MB86612PBT | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:IEEE 1394 Bus Controller (for MPEG, DVC) |
| MB86612PFV | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:IEEE 1394 Bus Controller (for MPEG, DVC) |
| MB86613 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:IEEE 1394 Open HCI Controller |
發布緊急采購，3分鐘左右您將得到回復。