參數資料
型號： MB86832-66PFV
廠商： FUJITSU LTD
元件分類： 微控制器/微處理器
英文描述： 32-bit Embedded Controller
中文描述： 32-BIT, 66 MHz, RISC MICROCONTROLLER, PQFP176
封裝： 24 X 24 MM, PLASTIC, QFP-176
文件頁數： 76/82頁
文件大?。?/td> 1373K
代理商： MB86832-66PFV
MB86830 Series
76
(2)Bus Control Register
Enable burst transfer after setting Cache Enable. To set Cache Disable, disable burst transfer in advance.
(3)System Support Control Register
Set Cache Enable before setting DRAM Burst Enable. To set Cache Disable, disable the DRAM Burst Enable
bit.
Before setting DRAM Burst Enable, be sure to set Burst Enable using the Bus Control Register.
The SAMEPAGE# pin may become “L” at the first CS4 access after setting Same Page Enable.
The Same Page circuit holds previous data even after the bus master is changed.
Set the Same Page Mask Register before setting Same Page Enable to “1”.
Before changing the Same Page Enable (bit 5) setting, set Cache Disable.
Set all of the Address Range Specifier Registers and Address Mask Registers before setting CS Enable to
“1”. (Set all of the Address Range Specifier Registers and Address Mask Registers even if any CS is not to
be used.)
Before changing the CS Enable (bit 4) setting, set Cache Disable.
When setting the Programmable Wait-state, be sure to set the Wait State Specifier Register.
(4)Wait State Specifier Register
Do not set the Wait Enable bit and the Single Cycle Non Burst Mode bit to “1” at the same time.
If the Single Cycle Non Burst Mode bit is set to “1” in the burst mode, the ready signal is generated in one
cycle regardless of the setting of the Single Cycle Burst Mode bit.
When setting the CS3 Wait State Specifier Register, be sure to set the Override bit to“1”. (The Wait State bit
can also be set to “1”.)
When the half-word load instruction is executed with CS3 in 16-bit Bus Mode, the CPU accesses twice but
the ready signal from the peripheral resource is generated only once. Therefore the CPU hangs at the second
access. To generate the second ready signal, set the Wait Enable bit to “1” (the CPU discards the data received
at the second access).
(5)Bus Width/Cacheable Register
In the DRAM Controller Enable state with CS4# = “L”, CS5 is handled as a Non-Cacheable signal.
In the DRAM Controller Enable state, the CS5 bus width follows the CS4 bus width setting. When the CS4
Bus Width Control bit has been set to (10)
2
, for example, the CS5 bus width is forced to be set to (10)
2
.
The CS3 Bus Width can be set only to the 16-bit or 32-bit bus width. When the 16-bit bus width is set, use
Half-Word Load (address “0”) or Half-Word Store (address “0”) to access the interrupt controller (IRC) and
DRAM controller registers.
(6)DRAM Refresh Timer Register
Be sure to set the Test Mode bit to “0”. Otherwise, TOVF# may not become “L”.
Since the timer performs counting based on the external clock, it is not affected by the multiplier circuit.
(7)Sleep Mode Register
To set the sleep mode (low power consumption mode), disable the caches.
The instruction to set the sleep mode (low power consumption mode) must be followed by at least three NOP
instructions.
(8)Trigger Mode Register
Set the Interrupt Mask Register to (ffff)
16
before changing the Trigger mode.
相關PDF資料
PDF描述
MB86833 32-bit Embedded Controller
MB86833PMT2 32-bit Embedded Controller
MB86834 32-bit Embedded Controller
MB86834-120PFV 32-bit Embedded Controller
MB86834PFV 32-bit Embedded Controller
相關代理商/技術參數
參數描述
MB86832-80PFV 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Embedded Controller
MB86833 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Embedded Controller
MB86833PMT2 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Embedded Controller
MB86834 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Embedded Controller
MB86834-120PFV 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Embedded Controller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*