- 您現在的位置：買賣IC網 > PDF目錄377895 > MB86961APF-G (Fujitsu Limited) UNIVERSAL INTERFACE FOR 10BASET PDF資料下載
參數資料
| 型號： | MB86961APF-G |
| 廠商： | Fujitsu Limited |
| 英文描述： | UNIVERSAL INTERFACE FOR 10BASET |
| 中文描述： | 通用接口10BASET |
| 文件頁數： | 6/29頁 |
| 文件大?。?/td> | 292K |
| 代理商： | MB86961APF-G |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
MB86961A
6
APPLICATIONS
Figure 1 shows the MB86961A in a typical application,
interfacing between a controller and the RJ45 connector
of the twisted-pair network. Figures 2 through 5 show
detailed diagrams of various MB86961A applications.
AUTO PORT SELECT LOOPBACK
CONTROL PIN
With MD0 and MD1 both tied high, the MB86961A logic
and framing are set to Mode 4 (compatible with National
NS8390 controllers).
The AUTOSEL pin is tied high, allowing the MB86961A
to automatically select the active port. The high at LI
enables Link Testing.
The UTP and NTH pins are both tied high selecting the
standard receiver threshold and 100
termination for
unshielded TP cable. (See Figure 2.)
MANUAL PORT SELECT LINK
TEST FUNCTION
With MD0 low and MD1 tied high, the MB86961A logic
and framing are set to Mode 3 (compatible with Fujitsu’s
MB86960 controller). As in Figure 3, the LI pin is tied
high, enabling Link Testing, and the UTP and NTH pins
are both tied high, selecting the standard receiver thresh-
old and 100
termination for unshielded TP cable. How-
ever, in this application AUTOSEL is tied low, allowing
external port selection through the PAUI pin. The remote
status output are inverted and used to drive LED indica-
tors. (See Figure 3.)
TWISTED-PAIR ONLY
Figure 4 shows the MB86961A is a typical twisted-pair
only application. The DTE is connected to a 10BASE-T
network through the twisted-pair RJ45 connector. (The
AUI port is not used.) With MD0 tied high and MD1
grounded, the MB86961A logic and framing are set to
Mode 2 (compatible with Intel 82586 controllers). The LI
pin externally controls the link test function. The UTP
and NTH pins are both tied low, selecting the reduced
receiver threshold and 150
termination for shielded TP
cable. The switch at LEDT/PDN manually controls the
power down mode. (See Figure 4.)
AUI ENCODER/DECODER ONLY
In this application, the DTE is connected to the coaxial
network through the AUI. AUTOSEL and PAUI are both
tied to ground, manually selecting the AUI port. The
twisted-pair port is not used. With MD1 and MD0 both
grounded, the MB86961A logic and framing are set to
Mode 1 (compatible with AMD AM7990 controllers).
The LI pin is tied low, disabling the link test function.
The LBK input controls loopback. A 20 MHz crystal con-
nected across CLKI and CLK0 provides the required
clock signal. (See Figure 5.)
Figure 1. Typical System Diagram
MB86960
Ethernet
MB86961A
10BASE-T Inter-
10BASE-T
AUI
B
U
H
O
S
相關PDF資料 |
PDF描述 |
|---|---|
| MB86965 | EtherCoupler ETHERNET CONTROLLER WITH 10BASE?T TRANSCEIVER |
| MB86965B | EtherCoupler ETHERNET CONTROLLER WITH 10BASE?T TRANSCEIVER |
| MB86965BPF-G-BND | EtherCoupler ETHERNET CONTROLLER WITH 10BASE?T TRANSCEIVER |
| MB86967 | LAN Controller with PC Card, ISA Bus, and General-purpose Bus Interfaces |
| MB86967PFV | LAN Controller with PC Card, ISA Bus, and General-purpose Bus Interfaces |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB86965 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:EtherCoupler ETHERNET CONTROLLER WITH 10BASE?T TRANSCEIVER |
| MB86965B | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:EtherCoupler ETHERNET CONTROLLER WITH 10BASE?T TRANSCEIVER |
| MB86965BPF-G-BND | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:EtherCoupler ETHERNET CONTROLLER WITH 10BASE?T TRANSCEIVER |
| MB86967 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:LAN Controller with PC Card, ISA Bus, and General-purpose Bus Interfaces |
| MB86967PFV | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:LAN Controller with PC Card, ISA Bus, and General-purpose Bus Interfaces |
發布緊急采購，3分鐘左右您將得到回復。