- 您現在的位置：買賣IC網 > PDF目錄69021 > MB90214PF 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP80 PDF資料下載
參數資料
| 型號： | MB90214PF |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP80 |
| 封裝： | PLASTIC, QFP-80 |
| 文件頁數： | 10/100頁 |
| 文件大?。?/td> | 1681K |
| 代理商： | MB90214PF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁
17
MB90210 Series
s HANDLING DEVICES
1. Preventing Latchup
CMOS ICs may cause latchup when a voltage higher than VCC or lower than VSS is applied to input or output
pins, or when a voltage exceeding the rating is applied between VCC and VSS.
If latch-up occurs, the power supply current increases rapidly, sometimes resulting in thermal breakdown of the
device. Use meticulous care not to let any voltage exceed the maximum rating.
Also, take care to prevent the analog power supply (AVCC and AVRH) and analog input from exceeding the digital
power supply (VCC) when the analog system power supply is turned on and off.
2. Treatment of Unused Input Pins
Leaving unused input pins open could cause malfunctions. They should be connected to a pull-up or pull-down
resistor.
3. Treatment of Pins when A/D is not Used
Connect to be AVCC = AVRH = VCC and AVSS = AVRL = VSS even if the A/D converter is not in use.
4. Precautions when Using an External Clock
To reset the internal circuit properly by the Low-level input to the RST pin, the “L” level input to the RST pin
must be maintained for at least five machine cycles. Pay attention to it if the chip uses external clock input.
5. VCC and VSS Pins
Apply equal potential to the VCC and VSS pins.
6. Supply Voltage Variation
The operation assurance range for the VCC supply voltage is as given in the ratings. However, sudden changes
in the supply voltage can cause misoperation, even if the voltage remains within the rated range. Therefore, it
is important to supply a stable voltage to the IC. The recommended power supply control guidelines are that
the commercial frequency (50 to 60 Hz) ripple variation (P-P value) on VCC should be less than 10% of the
standard VCC value and that the transient rate of change during sudden changes, such as during power supply
switching, should be less than 0.1 V/ms.
7. Notes on Using an External Clock
When using an external clock, drive the X0 pin as illustrated below. When an external clock is used, oscillation
stabilization time is required even for power-on reset and wake-up from stop mode.
X0
X1
MB90210
Note: When using an external clock, be sure to input external clock more than 6 machine cycles after
setting the HST pin to “L” to transfer to the hardware standby mode.
Use of External Clock
相關PDF資料 |
PDF描述 |
|---|---|
| MB90P214BPF | 16-BIT, OTPROM, 16 MHz, MICROCONTROLLER, PQFP80 |
| MB90W214ZF | 16-BIT, UVPROM, 16 MHz, MICROCONTROLLER, CQFP80 |
| MB90P653APFV | 16-BIT, OTPROM, 16 MHz, MICROCONTROLLER, PQFP100 |
| MB90V560CR | 16-BIT, 8 MHz, MICROCONTROLLER, CPGA256 |
| MB90V590ACR | 16-BIT, 16 MHz, MICROCONTROLLER, CPGA256 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90223 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90223PF | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90224 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90224PF | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90233 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。