- 您現在的位置：買賣IC網 > PDF目錄45187 > MB90394HAPMT 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP120 PDF資料下載
參數資料
| 型號： | MB90394HAPMT |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP120 |
| 封裝： | PLASTIC, LQFP-120 |
| 文件頁數： | 8/74頁 |
| 文件大小： | 886K |
| 代理商： | MB90394HAPMT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁
MB90390 Series
16
■ HANDLING DEVICES
Special care is required for the following when handling the device :
Preventing latch-up
Stabilization of supply voltage
Treatment of unused pins
Using external clock
Power supply pins (VCC/VSS)
Pull-up/down resistors
Crystal Oscillator Circuit
Turning-on Sequence of Power Supply to A/D Converter and Analog Inputs
Connection of Unused Pins of A/D Converter if A/D Converter is unused.
Notes on Energization
Caution on Operations during PLL Clock Mode
1.
Preventing latch-up
CMOS IC chips may suffer latch-up under the following conditions :
A voltage higher than VCC or lower than VSS is applied to an input or output pin.
A voltage higher than the rated voltage is applied between VCC and VSS.
The AVCC power supply is applied before the VCC voltage.
Latch-up may increase the power supply current drastically, causing thermal damage to the device.
For the same reason, also be careful not to let the analog power-supply voltage (AVCC, AVRH) exceed the digital
power-supply voltage.
2.
Stabilization of supply voltage
A sudden change in the supply voltage may cause the device to malfunction even within the specified VCC supply
voltage operating range. Therefore, the VCC supply voltage should be stabilized.
For reference, the supply voltage should be controlled so that VCC ripple variations (peak-to-peak values) at
commercial frequencies (50/60 Hz) fall below 10% of the standard VCC supply voltage and the coefficient of
fluctuation does not exceed 0.1 V/ms at instantaneous power switching.
3.
Treatment of unused pins
Leaving unused input pins open may result in misbehavior or latch up and possible permanent damage of the
device. Therefore they must be pulled up or pulled down through resistors. In this case those resistors should
be more than 2 k
.
Unused bidirectional pins should be set to the output state and can be left open, or the input state with the above
described connection.
4.
Using external clock
To use external clock, drive the X0 pin and leave X1 pin open.
X0
X1
MB90390 Series
相關PDF資料 |
PDF描述 |
|---|---|
| MB90V390HCR | 16-BIT, 24 MHz, MICROCONTROLLER, CPGA299 |
| MB90F395HPMT | 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP120 |
| MB90428GCPMC | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100 |
| MB90428GAPMC | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100 |
| MB90443GPF | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90420G | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-Bit Original Microcontroller |
| MB90420G_04 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-Bit Original Microcontroller |
| MB90420G_08 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-Bit Original Microcontroller |
| MB90423G | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-Bit Original Microcontroller |
| MB90423GA | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-Bit Original Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。