- 您現在的位置：買賣IC網 > PDF目錄377930 > MB90M408 (Fujitsu Limited) Octal Edge-Triggered D-type Flip-Flops With Clear 20-CDIP -55 to 125 PDF資料下載
參數資料
| 型號： | MB90M408 |
| 廠商： | Fujitsu Limited |
| 英文描述： | Octal Edge-Triggered D-type Flip-Flops With Clear 20-CDIP -55 to 125 |
| 中文描述： | F2MC - 16LX系列16位微控制器硬件手冊英文摘要 |
| 文件頁數： | 28/28頁 |
| 文件大?。?/td> | 213K |
| 代理商： | MB90M408 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁
8
6.
Handling Device
Preventing latch-up
Latch-up may occur in CMOSIC when a voltage higher than V
CC-CPU
or lower than V
SS-CPU
is applied to the
input or output pins, or a voltage exceeding the rated value is applied between V
CC-CPU
and V
SS-CPU
. Latch-
up may cause a rapid increase in the supply current, sometimes resulting in thermal damage to the device.
Therefore, keep the used voltage within the maximum ratings.
When turning the power on and off the analog supply voltage (AV
CC
) analog input should not exceed the
digital supply voltage (V
CC-CPU
).
Voltage supplies should be stabilized.
A sudden change of the power supply voltage may cause a malfunction even within the guaranteed range
of operation of the V
CC-CPU
power supply voltage.
For reference of stabilization, voltage variations are recommended to be restrained so that V
CC-CPU
ripple
variations (P-P values) are below 10% of the standard V
CC-CPU
value in commercial frequencies (50 to 60
Hz), and so that transient variation is below 0.1 V/ms in sudden changes during power switchovers.
Precautions when turning on the power supply
Ensure a minimum of 50
μ
s (between 0.2 to 2.7 V) for voltage rise times when turning on the power supply
to prevent malfunction of the built-in power reduction circuit.
Handling of unused input pins
Leaving unused input pins open may cause a malfunction. Therefore, these pins should be connected to a
pull-up
or a Pull-down resistor.
Handling of A/D converters power supply pins
Connect power supply pins with AV
CC
= V
CC-CPU
, AV
SS
= V
CC-IO
even when not using the A/D converters.
Precautions when using the external clock
Oscillating stability waiting time is required when resetting from the Power On Reset, Stop Mode when
using the external clock.
Order of turning on the power
Turn off the digital power supply (V
CC-CPU
) after turning off the A/D converter power supplie (AV
CC,
AV
SS
)
and analog input (AN0 to AN15).
Do not allow the input voltage to exceed AV
CC
when using the analog input pins as an input port.
相關PDF資料 |
PDF描述 |
|---|---|
| MB90MV405 | F2MC-16LX FAMILY 16-BIT MICROCONTROLLERS HARDWARE MANUAL ABSTRACTS |
| MB90M407APF | 16-Bit Original Microcontroller |
| MB90M407PF | 16-Bit Original Microcontroller |
| MB90M408APF | 16-Bit Original Microcontroller |
| MB90M408PF | 16-Bit Original Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90V340A-102CR | 制造商:FUJITSU 功能描述: |
| MB-910 | 制造商:Circuit Test 功能描述:BREADBOARD WIRING KIT - 350 PCS |
| MB9100100 | 制造商:COM/DUO 功能描述:FAN 4-6WKS |
| MB9100-100 | 制造商:COM/DUO 功能描述:FAN 4-6WKS |
| MB91101 | 制造商:Panasonic Industrial Company 功能描述:IC |
發布緊急采購，3分鐘左右您將得到回復。