- 您現在的位置：買賣IC網 > PDF目錄69022 > MB91354APMT 32-BIT, MROM, 50 MHz, RISC MICROCONTROLLER, PQFP176 PDF資料下載
參數資料
| 型號： | MB91354APMT |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 32-BIT, MROM, 50 MHz, RISC MICROCONTROLLER, PQFP176 |
| 封裝： | 0.50 MM PITCH, LEAD FREE, PLASTIC, LQFP-176 |
| 文件頁數： | 59/140頁 |
| 文件大?。?/td> | 3803K |
| 代理商： | MB91354APMT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁當前第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁
MB91350A Series
DS07-16503-5E
25
Pull-up Control
If a pull-up resistor is provided to a pin that is used as an external bus pin, there is no guarantee that the pin will
conform to the specifications given in “
■ ELECTRICAL CHARACTERISTICS 4. AC Characteristics (4) Normal
Bus Access Read/Write Operation, (5) Multiplex Bus Access Read/Write operation and (7) Hold Timing”.
Furthermore, even if a port has been configured to use a pull-up resistance, this setting is invalid during stop
mode with HIZ=1 and during hardware standby mode.
Sub Clock Select
At least one NOP instruction needs to be executed immediately after switching the clock source from main clock
mode to sub clock mode.
Bit Search Module
The BSD0, BSD1, and BDSC registers can only be accessed in words.
D-bus Memory
Do not set the code area to memory on the D-bus because instructions cannot be fetched from the D-bus.
Executing an instruction fetch to the D-bus area will cause incorrect data to be interpreted as code, possibly
causing the device to run out of control.
Low Power Consumption Mode
When entering sleep or stop mode, be sure to read the standby control register (STCR) immediately after writing
to it.
More specifically, use the following sequence.
Furthermore, after recovering from standby mode, set the I flag, ILM, and ICR registers such that the CPU
branches to the interrupt handler for the interrupt that triggered the controller to recover from standby mode.
Switching the Function of Shared Ports
Use the Port Function Register (PFR) to switch between using an external pin as a port or a shared pin. Note,
however, that bus pins are switched depending on the external bus settings.
(Idi
#0x0b, r0)
(Idi
#_CLKR, r12)
stb
r0, @r12
// sub-clock mode
nop
// Must insert NOP instruction
(Idi
#value_of_standby, r0)
(Idi
#_STCR, r12)
stb
r0, @r12
// set STOP/SLEEP bit
Idub @r12, r0
// Must read STCR
Idub @r12, r0
// after reading, go into standby mode
NOP
// Must insert NOP
× 5
NOP
相關PDF資料 |
PDF描述 |
|---|---|
| MB91F356BPMT | RISC MICROCONTROLLER, PQFP176 |
| MB91461PMC-GSE1 | RISC MICROCONTROLLER, PQFP176 |
| MB91664PMC | 32-BIT, MROM, 33 MHz, RISC MICROCONTROLLER, PQFP120 |
| MB91661PMC | 32-BIT, MROM, 33 MHz, RISC MICROCONTROLLER, PQFP120 |
| MB91F155PFV-G | 32-BIT, FLASH, 33 MHz, RISC MICROCONTROLLER, PQFP144 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB91355A | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontroller |
| MB91355APMT | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-Bit Proprietary Microcontroller |
| MB91360G | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit RISC Microcontroller |
| MB91360G_05 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit RISC Microcontroller |
| MB91366GA | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit RISC Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。