- 您現在的位置：買賣IC網 > PDF目錄67963 > MB95F118BWPMT 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PQFP48 PDF資料下載
參數資料
| 型號： | MB95F118BWPMT |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PQFP48 |
| 封裝： | 7 X 7 MM, 1.70 MM HEIGHT, 0.50 MM PITCH, PLASTIC, LFQFP-48 |
| 文件頁數： | 6/68頁 |
| 文件大?。?/td> | 2637K |
| 代理商： | MB95F118BWPMT |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
MB95110B Series
14
DS07-12615-3E
■ HANDLING DEVICES
Preventing Latch-up
Care must be taken to ensure that maximum voltage ratings are not exceeded when they are used.
Latch-up may occur on CMOS ICs if voltage higher than VCC or lower than VSS is applied to input and output pins
other than medium- and high-withstand voltage pins or if higher than the rating voltage is applied between VCC
pin and VSS pin.
When latch-up occurs, power supply current increases rapidly and might thermally damage elements.
Also, take care to prevent the analog power supply voltage (AVCC) and analog input voltage from exceeding the
digital power supply voltage (VCC) when the analog system power supply is turned on or off.
Stable Supply Voltage
Supply voltage should be stabilized.
A sudden change in power-supply voltage may cause a malfunction even within the guaranteed operating range
of the VCC power-supply voltage.
For stabilization, in principle, keep the variation in VCC ripple (p-p value) in a commercial frequency range
(50 Hz/60 Hz) not to exceed 10
% of the standard VCC value and suppress the voltage variation so that the
transient variation rate does not exceed 0.1 V/ms during a momentary change such as when the power supply
is switched.
Precautions for Use of External Clock
Even when an external clock is used, oscillation stabilization wait time is required for power-on reset, wake-up
from sub clock mode or stop mode.
Serial communication
There is a possibility to receive wrong data due to noise or other causes on the serial communication.
Therefore, design a printed circuit board so as to avoid noise.
Consider receiving of wrong data when designing the system. For example apply a checksum and retransmit
the data if an error occurs.
相關PDF資料 |
PDF描述 |
|---|---|
| MB95F118HWPMC | 8-BIT, FLASH, 10 MHz, MICROCONTROLLER, PQFP52 |
| MB95117HPMC | 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP52 |
| MB95F118TSPMC | 8-BIT, FLASH, 10 MHz, MICROCONTROLLER, PQFP52 |
| MB95F134MSPFV | 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PDSO28 |
| MB95F136MSPFV | 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PDSO28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB95F118BWPV2 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontrollers |
| MB95F118HWPMC-ESE1 | 制造商:FUJITSU 功能描述: |
| MB95F118JSPMC | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Microcontrollers |
| MB95F118JSPMC-GE1 | 制造商:FUJITSU 功能描述:8BIT MCU 60K FLASH 2K RAM LQFP52 |
| MB95F118JSPMCR-GE1 | 制造商:FUJITSU 功能描述:MCU 8-BIT 8FX 60K FLASH LQFP52 |
發布緊急采購，3分鐘左右您將得到回復。