- 您現在的位置：買賣IC網 > PDF目錄45197 > MB95F378EPMC2-G-SNE2 (FUJITSU LTD) 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PQFP64 PDF資料下載
參數資料
| 型號： | MB95F378EPMC2-G-SNE2 |
| 廠商： | FUJITSU LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PQFP64 |
| 封裝： | 12 X 12 MM, 1.70 MM HEIGHT, 0.65 MM PITCH, PLASTIC, LQFP-64 |
| 文件頁數： | 37/76頁 |
| 文件大小： | 2597K |
| 代理商： | MB95F378EPMC2-G-SNE2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁當前第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁
MB95310L/370L Series
42
DS07-12628-1E
(Continued)
*5: Applicable to the following pins: P00 to P07, P10, P11, P13 to P16, P20 to P22, P40 to P43, P50 to P53,
P60 to P67, P90 to P95, PA0 to PA3, PB0 to PB7, PC0 to PC7, PE0 to PE7, PG0
Use under recommended operating conditions.
Use with DC voltage (current).
The HV (High Voltage) signal is an input signal exceeding the VCC voltage. Always connect a limiting resistor
between the HV (High Voltage) signal and the microcontroller before applying the HV (High Voltage) signal.
The value of the limiting resistance should be set so that when the HV (High Voltage) signal is applied the
input current to the microcontroller pin does not exceed rated values, either instantaneously or for prolonged
periods.
When the microcontroller drive current is low, such as in low power consumption modes, the HV (High
Voltage) input potential may pass through the protective diode to increase the potential of the VCC pin, and
thus affects other devices.
If the HV (High Voltage) signal is input when the microcontroller power supply is off (not fixed at 0 V), since
power is supplied from the pins, incomplete operations may be executed.
If the HV (High Voltage) input is input after power-on, since power is supplied from the pins, the voltage
of power supply may not be sufficient to enable a power-on reset.
Do not leave the HV (High Voltage) input pin unconnected.
Example of a recommended circuit
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
HV(High Voltage) input (0 V to 16 V)
Protective diode
VCC
N-ch
P-ch
R
Limiting
resistor
Input/Output equivalent circuit
相關PDF資料 |
PDF描述 |
|---|---|
| MB95F374LPMC1-G-SNE2 | 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PQFP64 |
| MB95F378LPMC2-G-SNE2 | 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PQFP64 |
| MB95F376EPMC1-G-SNE2 | 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PQFP64 |
| MB95F374EPMC1-G-SNE2 | 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PQFP64 |
| MB95F398HPMC-G-SNE2 | 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PQFP48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB95F394H | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Microcontrollers |
| MB95F394HPMC1-G-SNE2 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Microcontrollers |
| MB95F394HPMC-G-SNE2 | 制造商:FUJITSU 功能描述:8-bit FX series microcontroller |
| MB95F394HWQN-G-SNE1 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Microcontrollers |
| MB95F394HWQN-G-SNERE1 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Microcontrollers |
發布緊急采購，3分鐘左右您將得到回復。