- 您現在的位置：買賣IC網 > PDF目錄45197 > MB95F478KPMC1-G-SNE2 (FUJITSU LTD) MICROCONTROLLER, PQFP64 PDF資料下載
參數資料
| 型號： | MB95F478KPMC1-G-SNE2 |
| 廠商： | FUJITSU LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | MICROCONTROLLER, PQFP64 |
| 封裝： | 10 X10 MM, 1.70 MM HEIGHT, 0.50 MM PITCH, PLASTIC, LQFP-64 |
| 文件頁數： | 20/76頁 |
| 文件大?。?/td> | 3707K |
| 代理商： | MB95F478KPMC1-G-SNE2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁
MB95410H/470H Series
DS702-00004-0v01-E
27
■ NOTES ON DEVICE HANDLING
Preventing latch-ups
When using the device, ensure that the voltage applied does not exceed the maximum voltage rating.
In a CMOS IC, if a voltage higher than VCC or a voltage lower than VSS is applied to an input/output pin that
is neither a medium-withstand voltage pin nor a high-withstand voltage pin, or if a voltage out of the rating
range of power supply voltage mentioned in "1. Absolute Maximum Ratings" of “
When a latch-up occurs, power supply current increases significantly, which may cause a component to be
thermally destroyed.
Stabilizing supply voltage
Supply voltage must be stabilized.
A malfunction may occur when power supply voltage fluctuates rapidly even though the fluctuation is within
the guaranteed operating range of the VCC power supply voltage.
As a rule of voltage stabilization, suppress voltage fluctuation so that the fluctuation in VCC ripple (p-p value)
at the commercial frequency (50 Hz/60 Hz) does not exceed 10% of the standard VCC value, and the transient
fluctuation rate does not exceed 0.1 V/ms at a momentary fluctuation such as switching the power supply.
Notes on using the external clock
When an external clock is used, oscillation stabilization wait time is required for power-on reset, wake-up
from subclock mode or stop mode.
■ PIN CONNECTION
Treatment of unused input pins
If an unused input pin is left unconnected, a component may be permanently damaged due to malfunctions
or latch-ups. Always pull up or pull down an unused input pin through a resistor of at least 2 k
Ω. Set an
unused input/output pin to the output state and leave it unconnected, or set it to the input state and treat it
the same as an unused input pin. If there is an unused output pin, leave it unconnected.
Power supply pins
To reduce unnecessary electro-magnetic emission, prevent malfunctions of strobe signals due to an increase
in the ground level, and conform to the total output current standard, always connect the VCC pin and the VSS
pin to the power supply and ground outside the device. In addition, connect the current supply source to the
VCC pin and the VSS pin with low impedance.
It is also advisable to connect a ceramic capacitor of approximately 0.1 F as a bypass capacitor between
the VCC pin and the VSS pin at a location close to this device.
DBG pin
Connect the DBG pin directly to an external pull-up resistor.
To prevent the device from unintentionally entering the debug mode due to noise, minimize the distance
between the DBG pin and the VCC or VSS pin when designing the layout of the printed circuit board.
The DBG pin should not stay at “L” level after power-on until the reset output is released.
RST pin
Connect the RST pin directly to an external pull-up resistor.
To prevent the device from unintentionally entering the reset mode due to noise, minimize the distance
between the RST pin and the VCC or VSS pin when designing the layout of the printed circuit board.
The RST/PF2 pin functions as the reset input/output pin after power-on. In addition, the reset output function
of the RST/PF2 pin can be enabled by the RSTOE bit in the SYSC register, and the reset input function or
the general purpose I/O function can be selected by the RSTEN bit in the SYSC register.
Analog power supply
Always set the same potential to AVCC and VCC pins. When VCC is larger than AVCC, the current may flow
through the AN00 to AN07 pins.
相關PDF資料 |
PDF描述 |
|---|---|
| MB95F476HPMC1-G-SNE2 | MICROCONTROLLER, PQFP64 |
| MB95F583HWQN-G-JNERE1 | 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PQCC32 |
| MB95F583KWQN-G-JNE1 | 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PQCC32 |
| MB95F564KPFT-G-JNE2 | 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PDSO20 |
| MB95F583KPFT-G-JNE2 | 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PDSO16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB95F478KPMC2-G-SNE2 | 制造商:FUJITSU 功能描述:8-bit MCUs |
| MB95F563HWQN-G-JNERE1 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Microcontrollers |
| MB95F564KPF-G-JNE2 | 功能描述:IC MCU 8BIT 20KB FLASH 20TSSOP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:8FX MB95560H 標準包裝:60 系列:PSOC® 3 CY8C38xx 核心處理器:8051 芯體尺寸:8-位 速度:67MHz 連通性:EBI/EMI，I²C，LIN，SPI，UART/USART 外圍設備:電容感應，DMA，LCD，POR，PWM，WDT 輸入/輸出數:25 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:2K x 8 RAM 容量:8K x 8 電壓 - 電源 (Vcc/Vdd):1.71 V ~ 5.5 V 數據轉換器:A/D 2x20b，D/A 4x8b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-VFQFN 裸露焊盤 包裝:托盤 |
| MB95F636HP-ES-SH-SNE2 | 制造商:FUJITSU 功能描述:8-bit MCU |
| MB95F636HPMC-ES-SNE2 | 制造商:FUJITSU 功能描述:8-bit FX series microcontroller |
發布緊急采購，3分鐘左右您將得到回復。