- 您現(xiàn)在的位置：買賣IC網 > PDF目錄45198 > MB95F564KWQN-G-JNERE1 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PQCC32 PDF資料下載
參數資料
| 型號： | MB95F564KWQN-G-JNERE1 |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PQCC32 |
| 封裝： | 5 X 5 MM, 0.80 MM HEIGHT, PLASTIC, QFN-32 |
| 文件頁數： | 38/84頁 |
| 文件大小： | 3941K |
| 代理商： | MB95F564KWQN-G-JNERE1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁當前第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁
MB95560H/570H/580H Series
DS702-00010-2v0-E
43
(Continued)
*1: The parameter is based on the condition that VSS is 0.0 V.
*2: VI and VO must not exceed VCC
+ 0.3 V. VI must not exceed the rated voltage. However, if the maximum
current to/from an input is limited by means of an external component, the ICLAMP rating is used instead of
the VI rating.
*3: Applicable to the following pins: P00 to P07, P62 to P64, PF0, PF1, PG1, PG2 (P00, and P62 to P64 are
only available on MB95F562H/F562K/F563H/F563K/F564H/F564K. P01, P02, P03, P07, PF0. PF1, PG1
and PG2 are only available on MB95F562H/F562K/F563H/F563K/F564H/F564K/F582H/F582K/F583H/
F583K/F584H/F584K.)
Use under recommended operating conditions.
Use with DC voltage (current).
The HV (High Voltage) signal is an input signal exceeding the VCC voltage. Always connect a limiting resistor
between the HV (High Voltage) signal and the microcontroller before applying the HV (High Voltage) signal.
The value of the limiting resistor should be set to a value at which the current to be input to the microcontroller
pin when the HV (High Voltage) signal is input is below the standard value, irrespective of whether the
current is transient current or stationary current.
When the microcontroller drive current is low, such as in low power consumption modes, the HV (High
Voltage) input potential may pass through the protective diode to increase the potential of the VCC pin,
affecting other devices.
If the HV (High Voltage) signal is input when the microcontroller power supply is off (not fixed at 0 V), since
power is supplied from the pins, incomplete operations may be executed.
If the HV (High Voltage) input is input after power-on, since power is supplied from the pins, the voltage
of power supply may not be sufficient to enable a power-on reset.
Do not leave the HV (High Voltage) input pin unconnected.
Example of a recommended circuit:
*4: P62 and P63 are only available on MB95F562H/F562K/F563H/F563K/F564H/F564K.
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
HV(High Voltage) input (0 V to 16 V)
Protective diode
VCC
N-ch
P-ch
R
Limiting
resistor
Input/Output equivalent circuit
相關PDF資料 |
PDF描述 |
|---|---|
| MB95F564HWQN-G-JNERE1 | 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PQCC32 |
| MB95F583KPF-G-JNE2 | 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PDSO16 |
| MB95F564HPF-G-JNE2 | 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PDSO20 |
| MB95F572KPF-G-JNE2 | 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PDSO8 |
| MB95F582KPFT-G-JNE2 | 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PDSO16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB95F636HP-ES-SH-SNE2 | 制造商:FUJITSU 功能描述:8-bit MCU |
| MB95F636HPMC-ES-SNE2 | 制造商:FUJITSU 功能描述:8-bit FX series microcontroller |
| MB95F636HWQN-ES-SNE1 | 制造商:FUJITSU 功能描述:8-bit MCU |
| MB95F636KP-ES-SH-SNE2 | 制造商:FUJITSU 功能描述:8-bit FX series microcontroller |
| MB95F636KPMC-ES-SNE2 | 制造商:FUJITSU 功能描述:8-bit FX series microcontroller |
發(fā)布緊急采購，3分鐘左右您將得到回復。