參數資料
型號： MBM29DL164BE-90
廠商： Fujitsu Limited
英文描述： 16M (2M X 8/1M X 16) BIT Dual Operation
中文描述： 16米（2米x 8/1M × 16）位雙操作
文件頁數： 38/75頁
文件大小： 1089K
代理商： MBM29DL164BE-90
MBM29DL16XTE/BE
-70/90/12
38
DQ
7
Data Polling
The MBM29DL16XTE/BE devices feature Data Polling as a method to indicate to the host that the Embedded
Algorithms are in progress or completed. During the Embedded Program Algorithm an attempt to read the
devices will produce the complement of the data last written to DQ
7
. Upon completion of the Embedded Program
Algorithm, an attempt to read the device will produce the true data last written to DQ
7
. During the Embedded
Erase Algorithm, an attempt to read the device will produce a “0” at the DQ
7
output. Upon completion of the
Embedded Erase Algorithm an attempt to read the device will produce a “1” at the DQ
7
output. The flowchart
for Data Polling (DQ
7
) is shown in Figure 24.
For programming, the Data Polling is valid after the rising edge of fourth write pulse in the four write pulse
sequence.
For chip erase and sector erase, the Data Polling is valid after the rising edge of the sixth write pulse in the six
write pulse sequence. Data Polling must be performed at sector address within any of the sectors being erased
and not a protected sector. Otherwise, the status may not be valid.
If a program address falls within a protected sector, Data Polling on DQ
7
is active for approximately 1
μ
s, then
that bank returns to the read mode. After an erase command sequence is written, if all sectors selected for
erasing are protected, Data Polling on DQ
7
is active for approximately 400
μ
s, then the bank returns to read mode.
Once the Embedded Algorithm operation is close to being completed, the MBM29DL16XTE/BE data pins (DQ
7
)
may change asynchronously while the output enable (OE) is asserted low. This means that the devices are
driving status information on DQ
7
at one instant of time and then that byte’s valid data at the next instant of time.
Depending on when the system samples the DQ
7
output, it may read the status or valid data. Even if the device
has completed the Embedded Algorithm operation and DQ
7
has a valid data, the data outputs on DQ
0
to DQ
6
may be still invalid. The valid data on DQ
0
to DQ
7
will be read on the successive read attempts.
The Data Polling feature is only active during the Embedded Programming Algorithm, Embedded Erase Algorithm
or sector erase time-out. (See Table 13.)
See Figure 9 for the Data Polling timing specifications and diagrams.
DQ
6
Toggle Bit I
The MBM29DL16XTE/BE also feature the “Toggle Bit I” as a method to indicate to the host system that the
Embedded Algorithms are in progress or completed.
During an Embedded Program or Erase Algorithm cycle, successive attempts to read (OE toggling) data from
the devices will result in DQ
6
toggling between one and zero. Once the Embedded Program or Erase Algorithm
cycle is completed, DQ
6
will stop toggling and valid data will be read on the next successive attempts. During
programming, the Toggle Bit I is valid after the rising edge of the fourth write pulse in the four write pulse sequence.
For chip erase and sector erase, the Toggle Bit I is valid after the rising edge of the sixth write pulse in the six
write pulse sequence. The Toggle Bit I is active during the sector time out.
In programming, if the sector being written to is protected, the toggle bit will toggle for about 1
μ
s and then stop
toggling without the data having changed. In erase, the devices will erase all the selected sectors except for the
ones that are protected. If all selected sectors are protected, the chip will toggle the toggle bit for about 400 μs
and then drop back into read mode, having changed none of the data.
Either CE or OE toggling will cause the DQ
6
to toggle. In addition, an Erase Suspend/Resume command will
cause the DQ
6
to toggle.
相關PDF資料
PDF描述
MBM29DL164BE70PBT 16M (2M X 8/1M X 16) BIT Dual Operation
MBM29DL164BE70PFTN 16M (2M x 8/1M x 16) BIT Dual Operation
MBM29DL161TD 16M (2M x 8/1M x 16) BIT Dual Operation
MBM29DL161TE70TR 16M (2M X 8/1M X 16) BIT Dual Operation
MBM29DL162BE70PBT 16M (2M X 8/1M X 16) BIT Dual Operation
相關代理商/技術參數
參數描述
MBM29DL164BE-90PBT 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M X 8/1M X 16) BIT Dual Operation
MBM29DL164BE-90TN 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M X 8/1M X 16) BIT Dual Operation
MBM29DL164BE-90TR 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M X 8/1M X 16) BIT Dual Operation
MBM29DL164TD 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16M (2M x 8/1M x 16) BIT Dual Operation
MBM29DL164TD-70PBT 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M X 8/1M X 16) BIT Dual Operation
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*