- 您現在的位置：買賣IC網 > PDF目錄377942 > MBM29F016-12 (Fujitsu Limited) CMOS 16M (2M x 8) Bit Flash Memory(CMOS 16M (2M x 8)位閃速存儲器) PDF資料下載
參數資料
| 型號： | MBM29F016-12 |
| 廠商： | Fujitsu Limited |
| 英文描述： | CMOS 16M (2M x 8) Bit Flash Memory(CMOS 16M (2M x 8)位閃速存儲器) |
| 中文描述： | 的CMOS 1,600（2米× 8）位閃存（1,600的CMOS（200萬× 8）位閃速存儲器） |
| 文件頁數： | 3/46頁 |
| 文件大?。?/td> | 520K |
| 代理商： | MBM29F016-12 |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
3
MBM29F016
-90/-12
I
GENERAL DESCRIPTION
The MBM29F016 is a 16 M-bit, 5.0 V-Only Flash memory organized as 2 M bytes of 8 bits each. The 2 M bytes
of data is divided into 32 sectors of 64 K bytes for flexible erase capability. The 8 bit of data will appear on DQ
to DQ
7
. The MBM29F016 is offered in a 48-pin TSOP package. This device is designed to be programmed in-
system with the standard system 5.0 V V
CC
supply. A 12.0 V V
The device can also be reprogrammed in standard EPROM programmers.
0
PP
is not required for program or erase operations.
The standard MBM29F016 offers access times between 90 ns and 120 ns allowing operation of high-speed
microprocessors without wait states. To eliminate bus contention the device has separate chip enable (CE), write
enable (WE), and output enable (OE) controls.
The MBM29F016 is command set compatible with JEDEC standard single-supply Flash standard. Commands
are written to the command register using standard microprocessor write timings. Register contents serve as
input to an internal state-machine which controls the erase and programming circuitry. Write cycles also internally
latch addresses and data needed for the programming and erase operations. Reading data out of the device is
similar to reading from 12.0 V Flash or EPROM devices.
The MBM29F016 is programmed by executing the program command sequence. This will invoke the Embedded
Program Algorithm which is an internal algorithm that automatically times the program pulse widths and verifies
proper cell margin. Each sector can be programmed and verified in less than 0.5 seconds. Erase is accomplished
by executing the erase command sequence. This will invoke the Embedded Erase Algorithm which is an
internal algorithm that automatically preprograms the array if it is not already programmed before executing the
erase operation. During erase, the device automatically times the erase pulse widths and verifies proper cell
margin.
This device also features a sector erase architecture. The sector erase mode allows for sectors of memory to
be erased and reprogrammed without affecting other sectors. A sector is typically erased and verified within 1
second (if already completely preprogrammed). The MBM29F016 is erased when shipped from the factory.
The MBM29F016 device also features hardware sector group protection. This feature will disable both program
and erase operations in any combination of eight sector groups of memory.
adjacent sectors grouped in the following pattern: sectors 0-3, 4-7, 8-11, 12-15, 16-19, 20-23, 24-27, and 28-31.
A sector group consists of four
Fujitsu has implemented an Erase Suspend feature that enables the user to put erase on hold for any period of
time to read data from or program data to a non-busy sector. Thus, true background erase can be achieved.
The device features single 5.0 V power supply operation for both read and program functions. Internally generated
and regulated voltages are provided for the program and erase operations. A low V
inhibits write operations during power transitions. The end of program or erase is detected by Data Polling of
DQ
7
, or by the Toggle Bit I feature on DQ
6
or RY/BY output pin. Once the end of a program or erase cycle has
been completed, the device automatically resets to the read mode.
CC
detector automatically
The MBM29F016 also has a hardware RESET pin. When this pin is driven low, execution of any Embedded
Program or Embedded Erase operations will be terminated. The internal state machine will then be reset into
the read mode. The RESET pin may be tied to the system reset circuity. Therefore, if a system reset occurs
during the Embedded Program or Embedded Erase operation, the device will be automatically reset to a read
mode. This will enable the system microprocessor to read the boot-up firmware from the Flash memory.
Fujitsu's Flash technology combines years of EPROM and E
of quality, reliability, and cost effectiveness. The MBM29F016 memory electrically erases all bits within a sector
simultaneously via Fowler-Nordheim tunneling. The bytes are programmed one byte at a time using the EPROM
programming mechanism of hot electron injection.
2
PROM experience to produce the highest levels
相關PDF資料 |
PDF描述 |
|---|---|
| MBM29F016-90 | CMOS 16M (2M x 8) Bit Flash Memory(CMOS 16M (2M x 8)位閃速存儲器) |
| MBM29F016A | 16M (2M X 8) BIT |
| MBM29F016A-12 | 1.65A, 2.7-5.5V Single Hot-Swap IC Hi-Side MOSFET, Fault Report, Act-High Enable 8-SOIC -40 to 85 |
| MBM29F016A-12PFTN | 16M (2M X 8) BIT |
| MBM29F016A-12PFTR | 16M (2M X 8) BIT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MBM29F016A | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M x 8) BIT |
| MBM29F016A-12 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M x 8) BIT |
| MBM29F016A-12PFTN | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16M (2M X 8) BIT |
| MBM29F016A-12PFTN-X# | 制造商:FUJITSU 功能描述: |
| MBM29F016A-12PFTR | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16M (2M X 8) BIT |
發布緊急采購，3分鐘左右您將得到回復。