參數資料
型號: MBM29F040C-90PFTR
廠商: FUJITSU LTD
元件分類: DRAM
英文描述: Single-Channel Current-Limited Power Distribution Switch 8-SOIC -40 to 85
中文描述: 512K X 8 FLASH 5V PROM, 90 ns, PDSO32
封裝: PLASTIC, REVERSE, TSOP1-32
文件頁數: 3/40頁
文件大?。?/td> 424K
代理商: MBM29F040C-90PFTR
3
MBM29F040C
-55/-70/-90
I
GENERAL DESCRIPTION
The MBM29F040C is a 4M-bit, 5.0 V-only Flash memory organized as 512K bytes of 8 bits each. The
MBM29F040C is offered in a 32-pin PLCC and 32-pin TSOP(I) package. This device is designed to be
programmed in-system with the standard system 5.0 V V
CC
supply. A 12.0 V V
PP
is not required for write or erase
operations. The device can also be reprogrammed in standard EPROM programmers.
The standard MBM29F040C offers access times 55 ns and 90 ns, allowing operation of high-speed
microprocessors without wait states. To eliminate bus contention the device has separate chip enable (CE), write
enable (WE), and output enable (OE) controls.
The MBM29F040C is pin and command set compatible with JEDEC standard E
2
PROMs. Commands are written
to the command register using standard microprocessor write timings. Register contents serve as input to an
internal state-machine which controls the erase and programming circuitry. Write cycles also internally latch
addresses and data needed for the programming and erase operations. Reading data out of the device is similar
to reading from 12.0 V Flash or EPROM devices.
The MBM29F040C is programmed by executing the program command sequence. This will invoke the Embedded
Program Algorithm which is an internal algorithm that automatically times the program pulse widths and verifies
proper cell margin. Typically, each sector can be programmed and verified in less than 0.5 seconds. Erase is
accomplished by executing the erase command sequence. This will invoke the Embedded Erase Algorithm which
is an internal algorithm that automatically preprograms the array if it is not already programmed before executing
the erase operation. During erase, the device automatically times the erase pulse widths and verifies proper cell
margin.
Any individual sector is typically erased and verified in 1 second. (If already completely preprogrammed.)
The device also features a sector erase architecture. The sector mode allows for 64K byte sectors of memory
to be erased and reprogrammed without affecting other sectors. The MBM29F040C is erased when shipped
from the factory.
The device features single 5.0 V power supply operation for both read and write functions. Internally generated
and regulated voltages are provided for the program and erase operations. A low V
CC
detector automatically
inhibits write operations on the loss of power. The end of program or erase is detected by Data Polling of DQ
7
or by the Toggle Bit feature on DQ
6
. Once the end of a program or erase cycle has been completed, the device
internally resets to the read mode.
Fujitsu's Flash technology combines years of EPROM and E
2
PROM experience to produce the highest levels
of quality, reliability and cost effectiveness. The MBM29F040C memory electrically erases the entire chip or all
bits within a sector simultaneously via Fowler-Nordheim tunneling. The bytes are programmed one byte at a
time using the EPROM programming mechanism of hot electron injection.
相關PDF資料
PDF描述
MBM29F080-12 8M (1M ×8) BIT Flash Memory(1M ×8 位5V 電源電壓閃速存儲器)
MBM29F080-90 8M (1M ×8) BIT Flash Memory(1M ×8 位5V 電源電壓閃速存儲器)
MBM29F080A-55 8M (1M X 8) BIT
MBM29F080A Single-Channel Current-Limited Power Distribution Switch 8-MSOP-PowerPAD -40 to 85
MBM29F080AC-90PF 8M (1M X 8) BIT
相關代理商/技術參數
參數描述
MBM29F080-90PFTN 制造商:FUJITSU 功能描述:
MBM29F080A 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 8M (1M x 8) BIT
MBM29F080A-55 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8M (1M X 8) BIT
MBM29F080A-55PF 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 8M (1M x 8) BIT
MBM29F080A-55PFTN 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 8M (1M x 8) BIT