- 您現在的位置：買賣IC網 > PDF目錄377943 > MBM29F040C-90PFTR (FUJITSU LTD) Single-Channel Current-Limited Power Distribution Switch 8-SOIC -40 to 85 PDF資料下載
參數資料
| 型號： | MBM29F040C-90PFTR |
| 廠商： | FUJITSU LTD |
| 元件分類： | DRAM |
| 英文描述： | Single-Channel Current-Limited Power Distribution Switch 8-SOIC -40 to 85 |
| 中文描述： | 512K X 8 FLASH 5V PROM, 90 ns, PDSO32 |
| 封裝： | PLASTIC, REVERSE, TSOP1-32 |
| 文件頁數： | 9/40頁 |
| 文件大?。?/td> | 424K |
| 代理商： | MBM29F040C-90PFTR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
9
MBM29F040C
-55/-70/-90
I
FUNCTIONAL DESCRIPTION
Read Mode
The MBM29F040C has two control functions which must be satisfied in order to obtain data at the outputs. CE
is the power control and should be used for a device selection. OE is the output control and should be used to
gate data to the output pins if a device is selected.
Address access time (t
ACC
) is equal to the delay from stable addresses to valid output data. The chip enable
access time (t
CE
) is the delay from stable addresses and stable CE to valid data at the output pins. The output
enable access time is the delay from the falling edge of OE to valid data at the output pins (assuming the
addresses have been stable for at least t
ACC
-t
OE
time).
Standby Mode
The MBM29F040C has two standby modes, a CMOS standby mode (CE input held at V
CC
±0.3 V.), when the
current consumed is less than 5 μA; and a TTL standby mode (CE is held at V
IH
) when the current required is
reduced to approximately 1 mA. During Embedded Algorithm operation, V
CC
Active current (I
CC2
) is required even
CE = V
IH
. The device can be read with standard access time (t
CE
) from either of these standby modes. In the
standby mode the outputs are in a high impedance state, independent of the OE input.
If the device is deselected during erasure or programming, the device will draw active current until the operation
is completed.
Output Disable
With the OE input at a logic high level (V
IH
), output from the device is disabled. This will cause the output pins
to be in a high impedance state.
Autoselect
The autoselect mode allows the reading out of a binary code from the device and will identify its manufacturer
and type. This mode is intended for use by programming equipment for the purpose of automatically matching
the device to be programmed with its corresponding programming algorithm. This mode is functional over the
entire temperature range of the device.
To activate this mode, the programming equipment must force V
ID
(11.5 V to 12.5 V) on address pin A
9
. Two
identifier bytes may then be sequenced from the device outputs by toggling address A
0
from V
IL
to V
IH
. All
addresses are DON’T CARES except A
0
, A
1
, and A
6
. (Recommend V
IL
for the other pins.)
The manufacturer and device codes may also be read via the command register, for instances when the
MBM29F040C is erased or programmed in a system without access to high voltage on the A
9
pin. The command
sequence is illustrated in Table 5. (Refer to Autoselect Command section.)
Byte 0 (A
0
= V
IL
) represents the manufacture’s code (Fujitsu = 04H) and byte 1 (A
0
= V
IH
) represents the device
identifier code (MBM29F040C = A4H). These two bytes are given in the Table 3. All identifiers for manufactures
and device will exhibit odd parity with the MSB (DQ
7
) defined as the parity bit. In order to read the proper device
codes when executing the autoselect, A
1
must be V
IL
. (See Table 3.)
相關PDF資料 |
PDF描述 |
|---|---|
| MBM29F080-12 | 8M (1M ×8) BIT Flash Memory(1M ×8 位5V 電源電壓閃速存儲器) |
| MBM29F080-90 | 8M (1M ×8) BIT Flash Memory(1M ×8 位5V 電源電壓閃速存儲器) |
| MBM29F080A-55 | 8M (1M X 8) BIT |
| MBM29F080A | Single-Channel Current-Limited Power Distribution Switch 8-MSOP-PowerPAD -40 to 85 |
| MBM29F080AC-90PF | 8M (1M X 8) BIT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MBM29F080-90PFTN | 制造商:FUJITSU 功能描述: |
| MBM29F080A | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 8M (1M x 8) BIT |
| MBM29F080A-55 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8M (1M X 8) BIT |
| MBM29F080A-55PF | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 8M (1M x 8) BIT |
| MBM29F080A-55PFTN | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 8M (1M x 8) BIT |
發布緊急采購，3分鐘左右您將得到回復。