參數資料
型號： MBM29LV017-90
廠商： Fujitsu Limited
英文描述： 16M (2M X 8) BIT
中文描述： 1,600（2米× 8）位
文件頁數： 18/52頁
文件大?。?/td> 600K
代理商： MBM29LV017-90
18
MBM29LV017
-80/-90/-12
Extended Command
(1) Fast Mode
MBM29LV017 has Fast Mode function. This mode dispenses with the initial two unlock cycles required in the
standard program command sequence by writing Fast mode command into the command register. In this mode,
the required bus cycle for programming is two cycles instead of four bus cycles in normal command. (Do not
write erase command in this mode.) The read operation is also executed after exiting this mode. To exit this
mode, it is necessary to write Fast Mode Reset command into the command register. (Refer to the Figure 23
Extended algorithm.) The V
CC
active current is required even CE = V
IH
during Fast Mode.
(2) Fast Programming
During Fast Mode, the programming can be executed with two bus cycles operation. The Embedded Program
Algorithm is executed by writing program Setup command (A0H) and data write cycles (PA/PD). (Refer to the
Figure 23 Extended algorithm.)
(3) CFI (Common Flash Memory Interface)
The CFI (Common Flash Memory Interface) specification outlines device and host system software interrogation
handshake which allows specific vender-specified software algorithms to be used for entire families of device.
This allows device-independent, JEDEC ID-independent, and forward- and backward-compatible software
support for the specified flash device families. Refer to CFI specification in detail.
The operation is initiated by writing the query command (98H) into the command register. Following the command
write, a read cycle from specific address retrives device information. Refer to the CFI code table. To terminate
operation, it is necessary to write the Read/Reset command sequence into the register.
(4) Extended Sector Protection
In addition to normal sector protection, the MBM29LV017 has Extended Sector Protection as extended function.
This function enable to protect sector by forcing V
ID
on RESET pin and write a command sequence. Unlike
conventional procedure, it is not necessary to force V
ID
and control timing for control pins. The only RESET pin
requires V
ID
for sector protection in this mode. The extended sector protect requires V
ID
on RESET pin. With this
condition, the operation is initated by writing the Setup command (60H) into the command register. Then, the
sector addresses pins (A
20
, A
19
, A
18
, A
17
, and A
16
) and (A
10
, A
6
, A
1
, A
0
) = (0, 0, 1, 0) should be set to the sector
to be protected (recommend to set V
IL
for the other addresses pins), and write extended sector protect command
(60H). A sector is typically protected in 150
μ
s. To verify programming of the protection cicuitry, the sector
addresses pins (A
20
, A
19
, A
18
, A
17
, and A
16
) and (A
10
, A
6
, A
1
, A
0
) = (0, 0, 1, 0) should be set and write a command
(40H). Following the command write, a logical “1” at device output DQ
0
will produce for protected sector in the
read operation. If the output data is logical “0”, please repeat to write extended sector protect command (60H)
again. To terminate the opetation, it is necessary to set RESET pin to V
IH
.
相關PDF資料
PDF描述
MBM29LV080-10 8M (1M ×8) Bit Flash Memory(8M (1M ×8)位 單5V 電源電壓閃速存儲器)
MBM29LV080-12 8M (1M ×8) Bit Flash Memory(8M (1M ×8)位 單5V 電源電壓閃速存儲器)
MBM29LV080-15 8M (1M ×8) Bit Flash Memory(8M (1M ×8)位 單5V 電源電壓閃速存儲器)
MBM29LV080A Audio codec with touch screen controller and power management monitor
MBM29LV080A-12 8M (1M x 8) BIT
相關代理商/技術參數
參數描述
MBM29LV017-90PBT 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16M (2M X 8) BIT
MBM29LV017-90PBT-SF2 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16M (2M X 8) BIT
MBM29LV017-90PTN 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16M (2M X 8) BIT
MBM29LV017-90PTR 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16M (2M X 8) BIT
MBM29LV080A 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8M (1M x 8) BIT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*