參數資料
型號： MBM29LV017-90
廠商： Fujitsu Limited
英文描述： 16M (2M X 8) BIT
中文描述： 1,600（2米× 8）位
文件頁數： 21/52頁
文件大小： 600K
代理商： MBM29LV017-90
21
MBM29LV017
-80/-90/-12
DQ
5
Exceeded Timing Limits
DQ
5
will indicate if the program or erase time has exceeded the specified limits (internal pulse count). Under
these conditions DQ
5
will produce a “1”. This is a failure condition which indicates that the program or erase
cycle was not successfully completed. Data Polling DQ
7
, DQ
6
is the only operating function of the device under
this condition. The CE circuit will partially power down the device under these conditions (to approximately 2
mA). The OE and WE pins will control the output disable functions as described in Table 2.
The DQ
5
failure condition may also appear if a user tries to program a non blank location without erasing. In this
case the device locks out and never completes the Embedded Algorithm operation. Hence, the system never
reads a valid data on DQ
7
bit and DQ
6
never stops toggling. Once the device has exceeded timing limits, the
DQ
5
bit will indicate a “1” Please note that this is not a device failure condition since the device was incorrectly
used. If this occurs, reset the device with command sequence.
DQ
3
Sector Erase Timer
After the completion of the initial Sector Erase command sequence the sector erase time-out will begin. DQ
3
will remain low until the time-out is complete. Data Polling and Toggle Bit are valid after the initial Sector Erase
command sequence.
If Data Polling or the Toggle Bit I indicates the device has been written with a valid erase command, DQ
3
may
be used to determine if the sector erase timer window is still open. If DQ
3
is high (“1”) the internally controlled
erase cycle has begun; attempts to write subsequent commands to the device will be ignored until the erase
operation is completed as indicated by Data Polling or Toggle Bit I. If DQ
3
is low (“0”), the device will accept
additional Sector Erase commands. To insure the command has been accepted, the system software should
check the status of DQ
3
prior to and following each subsequent sector erase command. If DQ
3
were high on the
second status check, the command may not have been accepted.
See Table 8: Hardware Sequence Flags.
DQ
2
Toggle Bit II
This Toggle Bit II, along with DQ
6
, can be used to determine whether the devices are in the Embedded Erase
Algorithm or in Erase Suspend.
Successive reads from the erasing sector will cause DQ
2
to toggle during the Embedded Erase Algorithm. If the
devices are in the erase-suspended-read mode, successive reads from the erase-suspended sector will cause
DQ
2
to toggle. When the devices are in the erase-suspended-program mode, successive reads from the byte
address of the non-erase suspended sector will indicate a logic “1” at the DQ
2
bit.
DQ
6
is different from DQ
2
in that DQ
6
toggles only when the standard program or Erase, or Erase Suspend
Program operation is in progress.
For example, DQ
2
and DQ
6
can be used together to determine the erase-suspend-read mode. (DQ
2
toggles
while DQ
6
does not.) See also above Table 9 and Figure 16.
Furthermore, DQ
2
can also be used to determine which sector is being erased. When the devices are in the
erase mode, DQ
2
toggles if this bit is read from the erasing sector.
相關PDF資料
PDF描述
MBM29LV080-10 8M (1M ×8) Bit Flash Memory(8M (1M ×8)位 單5V 電源電壓閃速存儲器)
MBM29LV080-12 8M (1M ×8) Bit Flash Memory(8M (1M ×8)位 單5V 電源電壓閃速存儲器)
MBM29LV080-15 8M (1M ×8) Bit Flash Memory(8M (1M ×8)位 單5V 電源電壓閃速存儲器)
MBM29LV080A Audio codec with touch screen controller and power management monitor
MBM29LV080A-12 8M (1M x 8) BIT
相關代理商/技術參數
參數描述
MBM29LV017-90PBT 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16M (2M X 8) BIT
MBM29LV017-90PBT-SF2 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16M (2M X 8) BIT
MBM29LV017-90PTN 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16M (2M X 8) BIT
MBM29LV017-90PTR 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16M (2M X 8) BIT
MBM29LV080A 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8M (1M x 8) BIT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*