- 您現在的位置：買賣IC網 > PDF目錄377949 > MBM29LV160TE12PBT (FUJITSU LTD) 16M (2M X 8/1M X 16) BIT PDF資料下載
參數資料
| 型號： | MBM29LV160TE12PBT |
| 廠商： | FUJITSU LTD |
| 元件分類： | DRAM |
| 英文描述： | 16M (2M X 8/1M X 16) BIT |
| 中文描述： | 2M X 8 FLASH 3V PROM, 120 ns, PBGA48 |
| 封裝： | PLASTIC, FBGA-48 |
| 文件頁數： | 23/59頁 |
| 文件大小： | 653K |
| 代理商： | MBM29LV160TE12PBT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁
MBM29LV160TE/BE
-70/90/12
23
DQ
6
Toggle Bit I
The MBM29LV160TE/BE also feature the “Toggle Bit I” as a method to indicate to the host system that the
Embedded Algorithms are in progress or completed.
During an Embedded Program or Erase Algorithm cycle, successive attempts to read (OE toggling) data from
the device will result in DQ
6
toggling between one and zero. Once the Embedded Program or Erase Algorithm
cycle is completed, DQ
6
will stop toggling and valid data can be read on the next successive attempts. During
programming, the Toggle Bit I is valid after the rising edge of the fourth WE pulse in the four write pulse sequence.
For chip erase and sector erase, the Toggle Bit I is valid after the rising edge of the sixth WE pulse in the six-
write pulse sequence. The Toggle Bit I is active during the sector time out.
In programming, if the sector being written to is protected, the toggle bit will toggle for about 2
μ
s and then stop
toggling without the data having changed. In erase, the device will erase all the selected sectors except for the
ones that are protected. If all selected sectors are protected, the chip will toggle the Toggle Bit I for about
200
μ
s and then drop back into read mode, having changed none of the data.
Either CE or OE toggling will cause the DQ
6
to toggle. In addition, an Erase Suspend/Resume command will
cause the DQ
6
to toggle.
See Figure 10 and Figure 23 for the Toggle Bit I timing specifications and diagram.
DQ
5
Exceeded Timing Limits
DQ
5
will indicate if the program or erase time has exceeded the specified limits (internal pulse count). Under
these conditions DQ
5
will produce a “1”. This is a failure condition which indicates that the program or erase
cycle was not successfully completed. Data Polling is the only operating function of the device under this
condition. The CE circuit will partially power down the device under these conditions. The OE and WE pins will
control the output disable functions as described in Tables 2 and 3.
The DQ
5
failure condition may also appear if a user tries to program a non blank location without erasing. In this
case the device locks out and never completes the Embedded Algorithm operation. Hence, the system never
reads a valid data on DQ
7
and DQ
6
never stops toggling. Once the device has exceeded timing limits, the DQ
5
bit will indicate a “1.” Please note that this is not a device failure condition since the device was incorrectly used.
If this occurs, reset the device with command sequence.
DQ
3
Sector Erase Timer
After the completion of the initial sector erase command sequence the sector erase time-out will begin. DQ
3
will
remain low until the time-out is complete. Data Polling and Toggle Bit I are valid after the initial sector erase
command sequence.
If Data Polling or the Toggle Bit I indicates the device has been written with a valid erase command, DQ
3
may
be used to determine if the sector erase timer window is still open. If DQ
3
is high (“1”) the internally controlled
erase cycle has begun; attempts to write subsequent commands to the device will be ignored until the erase
operation is completed as indicated by Data Polling or Toggle Bit I. If DQ
3
is low (“0”), the device will accept
additional sector erase commands. To insure the command has been accepted, the system software should
check the status of DQ
3
prior to and following each subsequent sector erase command. If DQ
3
is high on the
second status check, the command may not have been accepted.
See Table 8: Hardware Sequence Flags.
相關PDF資料 |
PDF描述 |
|---|---|
| MBM29LV160TE-90 | 16M (2M X 8/1M X 16) BIT |
| MBM29LV160TE12TN | 16M (2M X 8/1M X 16) BIT |
| MBM29LV160TE12TR | 16M (2M X 8/1M X 16) BIT |
| MBM29LV160TE70PBT | 16M (2M X 8/1M X 16) BIT |
| MBM29LV160TE70TN | 16M (2M X 8/1M X 16) BIT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MBM29LV160TE12PCV | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16M (2M X 8/1M X 16) BIT |
| MBM29LV160TE12TN | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16M (2M X 8/1M X 16) BIT |
| MBM29LV160TE12TR | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16M (2M X 8/1M X 16) BIT |
| MBM29LV160TE-70 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16M (2M X 8/1M X 16) BIT |
| MBM29LV160TE70PBT | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16M (2M X 8/1M X 16) BIT |
發布緊急采購，3分鐘左右您將得到回復。