- 您現在的位置：買賣IC網 > PDF目錄377953 > MBM29PDS322BE (Fujitsu Limited) 32M (2M x 16) BIT Page Dual Operation PDF資料下載
參數資料
| 型號： | MBM29PDS322BE |
| 廠商： | Fujitsu Limited |
| 英文描述： | 32M (2M x 16) BIT Page Dual Operation |
| 中文描述： | 32M的（2米× 16）位頁雙操作 |
| 文件頁數： | 26/66頁 |
| 文件大小： | 694K |
| 代理商： | MBM29PDS322BE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁
MBM29PDS322TE/BE
10/11
26
Erase Suspend/Resume
The Erase Suspend command allows the user to interrupt a Sector Erase operation and then perform data reads
from or programs to a sector not being erased. This command is applicable ONLY during the Sector Erase
operation which includes the time-out period for sector erase. Writing the Erase Suspend command (B0h) during
the Sector Erase time-out results in immediate termination of the time-out period and suspension of the erase
operation.
Writing the Erase Resume command (30h) resumes the erase operation. The bank addresses of sector being
erased or erase-suspended should be set when writing the Erase Suspend or Erase Resume command.
When the Erase Suspend command is written during the Sector Erase operation, the device will take a maximum
of “t
SPD
” to suspend the erase operation. When the device has entered the erase-suspended mode, the
RY/BY output pin will be at Hi-Z and the DQ
7
bit will be at logic “1”, and DQ
6
will stop toggling. The user must
use the address of the erasing sector for reading DQ
6
and DQ
7
to determine if the erase operation has been
suspended. Further writes of the Erase Suspend command are ignored.
When the erase operation has been suspended, the device defaults to the erase-suspend-read mode. Reading
data in this mode is the same as reading from the standard read mode except that the data must be read from
sectors that have not been erase-suspended. Successively reading from the erase-suspended sector while the
device is in the erase-suspend-read mode will cause DQ
2
to toggle. (See the section on DQ
2
.)
After entering the erase-suspend-read mode, the user can program the device by writing the appropriate com-
mand sequence for Program. This program mode is known as the erase-suspend-program mode. Again, pro-
gramming in this mode is the same as programming in the regular Program mode except that the data must be
programmed to sectors that are not erase-suspended. Successively reading from the erase-suspended sector
while the device is in the erase-suspend-program mode will cause DQ
2
to toggle. The end of the erase-suspended
Program operation is detected by the RY/BY output pin, Data polling of DQ
7
or by the Toggle Bit I (DQ
6
) which
is the same as the regular Program operation. Note that DQ
7
must be read from the Program address while DQ
6
can be read from any address within bank being erase-suspended.
To resume the operation of Sector Erase, the Resume command (30h) should be written to the bank being erase
suspended. Any further writes of the Resume command at this point will be ignored. Another Erase Suspend
command can be written after the chip has resumed erasing.
Extended Command
(1) Fast Mode
The device has Fast Mode function. This mode dispenses with the initial two unclock cycles required in the
standard program command sequence by writing Fast Mode command into the command register. In this
mode, the required bus cycle for programming is two cycles instead of four bus cycles in standard program
command. (Do not write erase command in this mode.) The read operation is also executed after exiting this
mode. To exit this mode, it is necessary to write Fast Mode Reset command into the command register. The
first cycle must contain the bank address. (Refer to the Figure 27.) The V
CC
active current is required even
CE = V
IH
during Fast Mode.
(2) Fast Programming
During Fast Mode, the programming can be executed with two bus cycles operation. The Embedded Program
Algorithm is executed by writing program set-up command (A0h) and data write cycles (PA/PD). (Refer to
the Figure 27.)
相關PDF資料 |
PDF描述 |
|---|---|
| MBM29PDS322TE | 32M (2M x 16) BIT Page Dual Operation |
| MBM29PDS322TE11 | 32M (2M x 16) BIT Page Dual Operation |
| MBM29PDS322TE11PBT | 32M (2M x 16) BIT Page Dual Operation |
| MBM29PDS322BE10 | 32M (2M x 16) BIT Page Dual Operation |
| MBM29PDS322BE10PBT | NEOZED TYPE,400V.10A |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MBM30000 | 功能描述:BRACKET SIDE MOUNT RoHS:是 類別:工業控制，儀表 >> 配件 系列:* 標準包裝:1 系列:Aero-Motive® 130117 附件類型:拖車帶 適用于相關產品:標準盒式跟蹤系統 其它名稱:WM6183 |
| MBM30035001 | 制造商:LG Corporation 功能描述:Card,Technical |
| MBM30035015 | 制造商:LG Corporation 功能描述:Card,Technical |
| MBM300A6 | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:IGBT MODULE RANGE WITH SOFT AND FAST (SFD) FREE-WHEELING DIODES |
| MBM300GR12A | 制造商:n/a 功能描述:IGBT Module |
發布緊急采購，3分鐘左右您將得到回復。