- 您現在的位置：買賣IC網 > PDF目錄377953 > MBM29PL160TD (Fujitsu Limited) 16M (2M x 8/1M x 16) BIT PDF資料下載
參數資料
| 型號： | MBM29PL160TD |
| 廠商： | Fujitsu Limited |
| 英文描述： | 16M (2M x 8/1M x 16) BIT |
| 中文描述： | 16米（2米x 8/1M × 16）位 |
| 文件頁數： | 18/51頁 |
| 文件大小： | 591K |
| 代理商： | MBM29PL160TD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁
18
MBM29PL160TD
-75/-90
/MBM29PL160BD
-75/-90
To resume the operation of Sector Erase, the Resume command (30H) should be written. Any further writes of
the Resume command at this point will be ignored. Another Erase Suspend command can be written after the
chip has resumed erasing.
Extended Command
(1) Fast Mode
MBM29PL160TD/BD has Fast Mode function. This mode dispenses with the initial two unlock cycles required
in the standard program command sequence writing Fast Mode command into the command register. In this
mode, the required bus cycle for programming is two cycles instead of four bus cycles in standard program
command. (Do not write erase command in this mode.) The read operation is also executed after exiting this
mode. To exit this mode, it is necessary to write Fast Mode Reset command into the command register.
(Refer to the Figure 22 Extended algorithm.) The V
CC
active current is required even CE = V
IH
during Fast
Mode.
(2) Fast Programming
During Fast Mode, the programming can be executed with two bus cycles operation. The Embedded Program
Algorithm is executed by writing program set-up command (A0H) and data write cycles (PA/PD). (Refer to
the Figure 22 Extended algorithm.)
(3) CFI (Common Flash Memory Interface)
The CFI (Common Flash Memory Interface) specification outlines device and host system software
interrogation handshake which allows specific vendor-specified software algorithms to be used for entire
families of devices. This allows device-independent, JEDEC ID-independent, and forward-and backward-
compatible software support for the specified flash device families. Refer to CFI specification in detail.
The operation is initiated by writing the query command (98H) into the command register. Following the
command write, a read cycle from specific address retrives device information. Please note that output data
of upper byte (DQ
8
to DQ
15
) is “0” in word mode (16 bit) read. Refer to the CFI code table. To terminate
operation, it is necessary to write the read/reset command sequence into the register.
相關PDF資料 |
PDF描述 |
|---|---|
| MBM29PL160BD-75 | 16M (2M x 8/1M x 16) BIT |
| MBM29PL160BD-75PF | 16M (2M x 8/1M x 16) BIT |
| MBM29PL160BD-75PFTN | Modular Connector |
| MBM29PL160BD-75PFTR | 16M (2M x 8/1M x 16) BIT |
| MBM29PL160BD-90 | 16M (2M x 8/1M x 16) BIT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MBM30000 | 功能描述:BRACKET SIDE MOUNT RoHS:是 類別:工業控制，儀表 >> 配件 系列:* 標準包裝:1 系列:Aero-Motive® 130117 附件類型:拖車帶 適用于相關產品:標準盒式跟蹤系統 其它名稱:WM6183 |
| MBM30035001 | 制造商:LG Corporation 功能描述:Card,Technical |
| MBM30035015 | 制造商:LG Corporation 功能描述:Card,Technical |
| MBM300A6 | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:IGBT MODULE RANGE WITH SOFT AND FAST (SFD) FREE-WHEELING DIODES |
| MBM300GR12A | 制造商:n/a 功能描述:IGBT Module |
發布緊急采購，3分鐘左右您將得到回復。