- 您現在的位置：買賣IC網 > PDF目錄371008 > MC13027DW (MOTOROLA INC) AMAX STEREO IC CHIPSET PDF資料下載
參數資料
| 型號： | MC13027DW |
| 廠商： | MOTOROLA INC |
| 元件分類： | 調諧器 |
| 英文描述： | AMAX STEREO IC CHIPSET |
| 中文描述： | AUDIO TUNER, PDSO20 |
| 封裝： | PLASTIC, SO-20 |
| 文件頁數： | 6/28頁 |
| 文件大?。?/td> | 586K |
| 代理商： | MC13027DW |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
MC13027 MC13122
AMAX STEREO CHIPSET
6
MOTOROLA ANALOG IC DEVICE DATA
What is AMAX
In 1993, a joint proposal by the EIA (Electronic Industries
Association) and the NAB (National Association of
Broadcasters) was issued. It included a unified standard for
pre–emphasis and distortion for broadcasters as well as a set
of criteria for the certification of receivers. The purpose of this
proposal was to restore quality and uniformity to the AM band
and to make it possible for the consumer to receive high
quality signals using the AM band. The FCC has been
supportive of this initiative and has required all new
broadcast licensees to meet AMAX standards. The NAB and
EIA have continued to encourage receiver manufacturers by
offering the AMAX certification logo to be displayed on all
qualifying radios. This logo is shown below.
or
The Receiver Criteria
An AMAX receiver must have wide bandwidth: 7.5kHz for
home and auto, 6.5 kHz for portables. It must have some
form of bandwidth control, either manual or automatic,
including at least two bandwidth provisions, such as “narrow”
and “wide”. It must meet NRSC receiver standards for
distortion and deemphasis. It must have provisions for an
external antenna. It must be capable of tuning the expanded
AM band (up to 1700 kHz). And finally, home and auto
receivers must have effective noise blanking. All of these
requirements, except the noise blanking, have been met by
Motorola’s previous AM radio products, such as MC13025
Front End and the MC13022A C–QUAM stereo decoder. It is
the Noise Blanker requirement which is met by the two
devices on this data sheet, the MC13027 and MC13122.
Noise blanking, especially in AM auto radios, has become
extremely important. The combination of higher energy
ignitions, using multiple spark coils, along with increased use
of plastic in the auto body, have increased the noise energy
at the radio. Also, the consumer has learned to expect higher
quality audio due to advances in many other media. For the
AM band to sustain interest to the consumer, a truly effective
noise blanker is required.
The block diagram below shows the Motorola AMAX
stereo chipset. It offers a two–pronged approach to noise
blanking which is believed to be the most effective yet offered
in the consumer market. The initial blanking takes place in
the output of the mixer, using a shunt circuit triggered by a
carefully defined wideband receiver. For most noises, some
residual audible disturbance is almost always still present
after this process. The disturbance becomes stretched and
delayed as it passes through the rest of the selectivity in the
receiver. The stretching and delay are predictable, so the
MC13027 can provide a noise blanking pulse with the correct
delay and stretch to the output stages of the MC13122
decoder. The MC13122 has a Track and Hold circuit which
receives the blanking signal from the Front End and uses it to
gently hold the audio wherever it is as the pulse arrives, and
hold that value until the noise has passed. The combined
effect is dramatic. A wide range of types of noise is
successfully suppressed and the resulting audio seems
almost clean until the noise is so intense that the blanking
approaches full–time.
The amount of extra circuitry to accomplish noise blanking
is relatively small. The external components for this added
capability are shown in Figure 3. In the MC13027 Front end,
the noise receiver/detector requires two capacitors. The
presettings for blanking timing and blanking delay require
three external fixed resistors. Finally the decoder requires
two track and hold capacitors to store the “audio” voltage
during the track and hold function.
Figure 3. AMAX Stereo Receiver with Noise Blanker
MC13027
MC13122
Audio Blank
450 kHz
Filter
RF Attenuate
Left
Right
RF In
Pin
Diode
Reset
AGC
RF
Amplifier
Mixer
IF
Amplifier
AGC’d IF
Amplifier
AM
Stereo
Decoder
Track
and
Hold
Variable
Notch Filter
Wideband
AGC
4.0 V
Regulator
Divide
by 4
VCO
RF
Attenuator
Switch
RF Blank
Timer
AGC’d RF
Amplifier
AM
Detector
Audio
Reject
Filter
Pulse
Detector
Delay
Timer
Audio Blank
Timer
Audio
Blank
Switch
相關PDF資料 |
PDF描述 |
|---|---|
| MC13027P | AMAX STEREO IC CHIPSET |
| MC13122P | CONNECTOR KIT, JPS130PT; RoHS Compliant: Yes |
| MC13135DW | DUAL CONVERSION NARROWBAND FM RECEIVERS |
| MC13136 | DUAL CONVERSION NARROWBAND FM RECEIVERS |
| MC13135P | DUAL CONVERSION NARROWBAND FM RECEIVERS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC13027P | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:AMAX STEREO IC CHIPSET |
| MC13028A | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:C-QUAM AM STEREO ADVANCED WIDE VOLTAGE IF and DECODER for E.T.R. RADIOS |
| MC13028AD | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:C-QUAM AM STEREO ADVANCED WIDE VOLTAGE IF and DECODER for E.T.R. RADIOS |
| MC13028AP | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:C-QUAM AM STEREO ADVANCED WIDE VOLTAGE IF and DECODER for E.T.R. RADIOS |
| MC13030 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:DUAL CONVERSION AM RECEIVER |
發布緊急采購，3分鐘左右您將得到回復。