參數資料
型號: MC14051BDR2
廠商: ON Semiconductor
文件頁數: 11/12頁
文件大?。?/td> 0K
描述: IC MUX/DEMUX 8X1 16SOIC
標準包裝: 1
系列: 4000B
功能: 多路復用器/多路分解器
電路: SP8T
導通狀態電阻: 280 歐姆
電壓電源: 雙電源
電壓 - 電源,單路/雙路(±): ±3 V ~ 18 V
電流 - 電源: 360nA
工作溫度: -55°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 16-SOIC(0.154",3.90mm 寬)
供應商設備封裝: 16-SOIC
包裝: 標準包裝
其它名稱: MC14051BDR2OSDKR
MC14051B, MC14052B, MC14053B
http://onsemi.com
8
APPLICATIONS INFORMATION
Figure A illustrates use of the onchip level converter
detailed in Figures 2, 3, and 4. The 0to5 V Digital Control
signal is used to directly control a 9 Vpp analog signal.
The digital control logic levels are determined by VDD
and VSS. The VDD voltage is the logic high voltage; the VSS
voltage is logic low. For the example, VDD = + 5 V = logic
high at the control inputs; VSS = GND = 0 V = logic low.
The maximum analog signal level is determined by VDD
and VEE. The VDD voltage determines the maximum
recommended peak above VSS. The VEE voltage
determines the maximum swing below VSS. For the
example, VDD VSS = 5 V maximum swing above VSS;
VSS VEE = 5 V maximum swing below VSS. The example
shows a
± 4.5 V signal which allows a 1/2 volt margin at each
peak. If voltage transients above VDD and/or below VEE are
anticipated on the analog channels, external diodes (Dx) are
recommended as shown in Figure B. These diodes should be
small signal types able to absorb the maximum anticipated
current surges during clipping.
The absolute maximum potential difference between
VDD and VEE is 18.0 V. Most parameters are specified up to
15 V which is the recommended maximum difference
between VDD and VEE.
Balanced supplies are not required. However, VSS must
be greater than or equal to VEE. For example, VDD = + 10
V, VSS = + 5 V, and VEE – 3 V is acceptable. See the Table
below.
Figure A. Application Example
+5 V
- 5 V
VDD
VSS
VEE
9 Vp-p
ANALOG SIGNAL
0-TO-5 V DIGITAL
CONTROL SIGNALS
SWITCH
I/O
INHIBIT,
A, B, C
COMMON
O/I
9 Vp-p
ANALOG SIGNAL
+ 4.5 V
4.5 V
GND
+5 V
EXTERNAL
CMOS
DIGITAL
CIRCUITRY
MC14051B
MC14052B
MC14053B
Figure B. External Germanium or Schottky Clipping Diodes
VDD
VEE
DX
ANALOG
I/O
COMMON
O/I
POSSIBLE SUPPLY CONNECTIONS
VDD
In Volts
VSS
In Volts
VEE
In Volts
Control Inputs
Logic High/Logic Low
In Volts
Maximum Analog Signal Range
In Volts
+ 8
0
– 8
+ 8/0
+ 8 to – 8 = 16 Vp–p
+ 5
0
– 12
+ 5/0
+ 5 to – 12 = 17 Vp–p
+ 5
0
0
+ 5/0
+ 5 to 0 = 5 Vp–p
+ 5
0
– 5
+ 5/0
+ 5 to – 5 = 10 Vp–p
+ 10
+ 5
– 5
+ 10/ + 5
+ 10 to – 5 = 15 Vp–p
相關PDF資料
PDF描述
VE-2TJ-IY-F1 CONVERTER MOD DC/DC 36V 50W
VI-21J-CV-B1 CONVERTER MOD DC/DC 36V 150W
UPD70F3453GC-8EA-A MCU 32BIT 128KB FLASH 100LQFP
VE-2T4-IY-F3 CONVERTER MOD DC/DC 48V 50W
VE-2T4-IY-F2 CONVERTER MOD DC/DC 48V 50W
相關代理商/技術參數
參數描述
MC14051BDR2G 功能描述:多路器開關 IC 3-18V SP8T Analog Sw -55 to 125 deg C RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻(最大值):7 Ohms 開啟時間(最大值): 關閉時間(最大值): 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16
MC14051BDT 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel
MC14051BDTEL 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC14051BDTR2 功能描述:多路器開關 IC 3-18V SP8T Analog Sw RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻(最大值):7 Ohms 開啟時間(最大值): 關閉時間(最大值): 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16
MC14051BDTR2G 功能描述:多路器開關 IC 3-18V SP8T Analog Sw -55 to 125 deg C RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻(最大值):7 Ohms 開啟時間(最大值): 關閉時間(最大值): 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16