參數資料
型號： MC33389ADW
廠商： MOTOROLA INC
元件分類： 網絡接口
英文描述： System Basis Chip with Low Speed Fault Tolerant CAN
中文描述： DATACOM, INTERFACE CIRCUIT, PDSO28
封裝： PLASTIC, SO-28
文件頁數： 17/35頁
文件大小： 609K
代理商： MC33389ADW
MC33389
17
MC33389
WAKE-UP CAPABILITIES
Wake-up By SPI
In some applications, the microcontroller might be
supplied by an external VDD and remains powered in SBC
Sleep mode. In this case, a feature is provided which makes
possible to wake-up the SBC by SPI activity.
After V1 is totally switched off in sleep mode (V1<1.5V), if
a falling edge occurs on CSB (crossing 2.5V threshold), a
wake-up by SPI is detected, the SBC switches to
NormalRequest mode. A flag is set in ISR2.
Interrupt Output
The INTB output may be activated in the following cases:
V
bat
overvoltage (BatHigh)
V
bat
undervoltage (BatFail)
High temperature on V1 or V2
Pre-warning temperature on V1 or V2
CAN bus failure
SPI error
Local wake-up (can be used for low battery detection)
Bus wake-up
All these interrupts are maskable (See Register
Description Section).
RSTB Input/Output
The RSTB (reset) pin is an input/output pin. The typical
reset duration from SBC to microcontroller is 1ms. If longer
times are required, an external capacitor can be used. SBC
provides two RSTB output pull-up currents.
A typical 30
μ
A pull up when Vreset is below 2.5V and a
300uA pull up when reset voltage is higher than 2.5V.
RSTB is also an input for the SBC. It means the MC33389
is forced to NormalRequest mode after RSTB is released by
the microcontroller
General
When normally working in two-wire operating mode, the
CAN transmission can afford some ground shift between
different nodes without trouble. Nevertheless, in case of bus
failure, the transceiver switches to single-wire operation,
therefore working with less noise margin. The affordable
ground shift is decreased in this case.
The SBC is provided with a ground shift detection for
diagnosis purpose. Four ground shift levels are selectable
and the detection is stored in the GSLR register which is
accessible via the SPI.
Normal and
Standby
Detection active according to the option.
The event is stored in WUISR register.The
SBC may activate INTB output.
Real time state of each wake-up input
pin available in WUIRTI register
Sleep
Detection active according to the option.
The event is stored in WUISR register. The
SBC switches to NormalRequest mode
Emergency
No detection
SBC Modes
Local Wake-up Behaviour
GND SHIFT DETECTION
Detection Principle
The gnd shift to detect is selected via the SPI out of 4
different values (-0.7V, -1.2V, -1.7V, -2.2V). At each TX falling
edge (end of recessive state) CANH voltage is sensed. If it is
detected to be below the selected gnd shift threshold, the bit
SHIFT is set at 1 in GSLR register. No filter is implemented.
Required filtering for reliable detection should be done by
software (e.g. several trials).
The MC33389 is proposed in several package versions,
and also offers slight differences in term of functionalities.
The device version is identified in the device part number
by the first letter after the 389 number.
The package identification is done by the last two letters of
the part number (DW for SO28 wide body, DH for power
SO20).
Differences between A, C and D versions:
Behavior for V1 low:
A version
:
If V1 is below reset threshold, device enters reset mode,
and if V1 stays below reset threshold for more than 100ms,
then the SBC automatically enters sleep mode. This could be
the case if V1 is shorted or permanently over loaded, and
going to sleep mode would then avoid system over current
consumption.
This concerns the device reference: MC33389ADW and
MC33389ADH.
C and D versions
:
If V1 is below reset threshold, the SBC enters and stays in
reset mode (reset low) permanently.
This concerns the device reference: MC33389CDW and
MC33389CDH and MC33389DDW
Reset threshold specification:
A and C versions:
The reset threshold is defined per table “electrical
parameter, V1 pin 5V.
This concerns device MC33389ADW, ADH, CDW and
CDH
D version
: The reset threshold for the D version is slightly
higher than the A and C versions. Refer to device electrical
parameter table, V1 pin 5V
This concerns device reference MC33389DDW.
DEVICE DIFFERENT VERSIONS
F
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
.
相關PDF資料
PDF描述
MC33389CDH System Basis Chip with Low Speed Fault Tolerant CAN
MC33389CDW System Basis Chip with Low Speed Fault Tolerant CAN
MC33389DDW System Basis Chip with Low Speed Fault Tolerant CAN
MC33463H-33KT1 VARIABLE FREQUENCY MICROPOWER DC-to-DC CONVERTER
MC33463H-30KT1 VARIABLE FREQUENCY MICROPOWER DC-to-DC CONVERTER
相關代理商/技術參數
參數描述
MC33389CDH 功能描述:IC SYSTEM BASIS W/CAN 20-HSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A
MC33389CDHR2 功能描述:IC SYSTEM BASE W/CAN 20-HSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A
MC33389CDW 功能描述:網絡控制器與處理器 IC SYSTEM BASIC CHIPS RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MC33389CDWR2 功能描述:網絡控制器與處理器 IC SYSTEM BASIC CHIPS RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MC33389DDW 功能描述:網絡控制器與處理器 IC SBC SOW28 RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*