- 您現在的位置：買賣IC網 > PDF目錄11546 > MC33389CDW (Freescale Semiconductor)IC SYSTEM BASE W/CAN 28-SOIC PDF資料下載
參數資料
| 型號： | MC33389CDW |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 11/49頁 |
| 文件大小： | 0K |
| 描述： | IC SYSTEM BASE W/CAN 28-SOIC |
| 標準包裝： | 26 |
| 控制器類型： | 系統基礎芯片 |
| 接口： | CAN |
| 電源電壓： | 5.5 V ~ 18 V |
| 電流 - 電源： | 45mA |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 28-SOIC W |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
19
33389
FUNCTIONAL DEVICE OPERATION
Supply and VBAT Block
VBAT Monitoring—VBAT is the main power supply coming
from the battery voltage after an external protection diode
(for reverse battery). VBAT is monitored for under voltage
and over voltage.
VBAT Under Voltage—VBAT is monitored for under voltage
if it is below 4.0 V the BatFail flag is set in the VSSR
register and a maskable interrupt is sent to the
microcontroller.
VBAT Over Voltage— When VBAT is > 20 V, the BatHigh
flag is set in the VSSR register. A maskable interrupt is
sent to the microcontroller. No specific action is taken to
reduce current consumption (to limit power dissipation).
This is to allow the entire flexibility to the microcontroller for
a decision.
CAN Transceiver
The device incorporates a low speed 125 kBaud CAN
physical interface. Its electrical parameters for the CANL,
CANH, RTL,RTH, RX, and TX pins are identical to the 33388,
stand alone CAN physical interface.
The mode control for the CAN transceiver (Normal, VBAT
Stand-by, Sleep, etc.) are selectable through the 33389 SPI
interface.
Baud Rate up to 125 kBit/s
Supports unshielded bus wires
Short-circuit proof to battery and ground in 12 V powered
systems
Supports single-wire transmission modes with ground
offset voltages up to 1.5 V
Automatic switching to single wire mode in case of bus
failures
Automatic reset to differential mode if bus failure is
removed
Low Electromagnetic Interference (EMI) due to built-in
slope control and signal symmetry
Fully integrated receiver filters
Thermally protected
Bus lines protected against automotive transients
Low current Bus Stand-by mode with wake-up capability
via the bus
An unpowered node does not disturb the bus lines
Figure 5. CAN Simplified Block Diagram
CONSEQUENCE OF FAILURE DETECTIONS
S1 is the switch from RTH to Ground
S2 is the switch from RTL to V2 and
S3 is the switch from RTL to VBAT
Each failure type provides data concerning which switch is
open and which driver is disabled.
Failure 1: Nothing done
Failure 2: Nothing done
Failure3: S1 open. Driver CANH is disabled
Failure4: S2 and S3 open. Driver CANL is disabled
Failure5: Nothing done
Failure6: S2 and S3 open. Driver CANL disabled
Failure7: S2 and S3 open. Driver CANL disabled
Failure8: S1 Open. CANH driver disable
CAN Transceiver Description
The CAN transceiver is an interface between CAN
protocol controller and the physical bus. It is intended for low
—
In Sleep Mode, During
Disable Time of Cyclic
Sense if Configured
—
Over Temp Threshold Reached
—
V1 Disabled (for any reason)
—
V2 Over Temperature Shutdown
Table 8. V3 Control
Termination
Protection
RX
TX
CAN_H
CAN_L
RTH
RTL
VDD2
SPI
Transmitter
Receiver
- Fail Detect
- Receive Mode
VDD2 VBAT
CAN Transceiver Register
Drivers
CAN transceiver simplified block diagram
12.5k
S3
S2
S1
VDD BAT
RTL
CANH
CANL
RTH
相關PDF資料 |
PDF描述 |
|---|---|
| MC33388DR2 | IC TOLERANT CAN INT FAULT 14SOIC |
| PX0414 | CONN SMB JACK PNL MNT RG174 |
| PIC16LF1937-E/PT | IC PIC MCU FLASH 512KX14 44-TQFP |
| PIC16F1934-E/ML | IC PIC MCU FLASH 256KX7 44-QFN |
| V48C12M75B | CONVERTER MOD DC/DC 12V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC33389CDWR2 | 功能描述:網絡控制器與處理器 IC SYSTEM BASIC CHIPS RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| MC33389DDW | 功能描述:網絡控制器與處理器 IC SBC SOW28 RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| MC33389DDWR2 | 功能描述:網絡控制器與處理器 IC SBC SOW28 RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| MC33390D | 功能描述:IC TRANSCEIVER SER LINK 8-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| MC33390DR2 | 功能描述:IC TRANSCEIVER SER LINK 8-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。