- 您現在的位置：買賣IC網 > PDF目錄11546 > MC33389CDW (Freescale Semiconductor)IC SYSTEM BASE W/CAN 28-SOIC PDF資料下載
參數資料
| 型號： | MC33389CDW |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 9/49頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SYSTEM BASE W/CAN 28-SOIC |
| 標準包裝： | 26 |
| 控制器類型： | 系統基礎芯片 |
| 接口： | CAN |
| 電源電壓： | 5.5 V ~ 18 V |
| 電流 - 電源： | 45mA |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 28-SOIC W |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
17
33389
FUNCTIONAL DESCRIPTION
INTRODUCTION
FUNCTIONAL DESCRIPTION
INTRODUCTION
The System Basis Chip (SBC) is an integrated circuit
dedicated to car body applications. It includes three main
blocks:
1. A dual voltage regulator
2. Reset, watchdog, wake-up inputs, cyclic wake-up
3. CAN low speed fault tolerant physical interface
Supplies
Two low drop regulators and one switch to VBAT are
provided to supply the ECU microcontroller or peripherals,
with independent control and monitoring through SPI.
FUNCTIONAL PIN DESCRIPTION
TRANSMIT AND RECEIVE DATA (TX AND RX)
The RX and TX pins (receive data and transmit data pins,
respectively) are connected to a microcontroller’s CAN
protocol handler. TX is an input and controls the CANH and
CANL line state (dominant when TX is LOW, recessive when
TX is HIGH). RX is an output and reports the bus state.
VOLTAGE REGULATOR ONE AND TWO
(V1 AND V2)
The V1 pin is a 3% low drop voltage regulator dedicated to
the microcontroller supply (nominal 5V supply).
The V2 pin is a low drop voltage regulator dedicated to the
peripherals supply (nominal 5V supply).
RESET (RST)
The RST (reset) pin is an input/output pin. The typical
reset duration from SBC to microcontroller is 1ms. If longer
times are required, an external capacitor can be used. SBC
provides two RST output pull-up currents. A typical 30A pull
up when Vreset is below 2.5V and a 300uA pull up when
reset voltage is higher than 2.5V. RST is also an input for the
SBC. It means the MC33389 is forced to Normal Request
mode after RST is released by the microcontroller
INTERRUPT (INT)
The Interrupt pin INT is an output that is set LOW when an
interrupt occurs. INT is enabled using the Interrupt Register
(INTR). When an interrupt occurs, INT stays LOW until the
interrupt source is cleared.
INT output also reports a wake-up event.
GROUND (GND)
This pin is the ground of the integrated circuit.
MASTER IN/ SLAVE OUT (MISO)
MISO is the Master In Slave Out pin of the serial peripheral
interface. Data is sent from the SBC to the microcontroller
through the MISO pin.
MASTER OUT/ SLAVE IN (MOSI)
MOSI is the Master Out Slave In pin of the serial peripheral
interface. Control data from a microcontroller is received
through this pin.
SYSTEM CLOCK (SCLK)
This pin clocks the internal shift registers for SPI
communication.
CHIP SELECT (CS)
CS is the Chip Select pin of the serial peripheral interface
(SPI). When this pin is LOW, the SPI port of the device is
selected.
LEVEL 0-2 INPUTS (L0: L2)
The L0: L2 pins can be connected to contact switches or
the output of other ICs for external inputs. The input states
can be read by the SPI. These inputs can be used as wake-
up events for the SBC.
NO CONNECT (NC)
No pin connection.
TERMINATION RESISTANCE (HIGH AND LOW?)
(RTH AND RTL)
External CAN bus high and low termination resistance pins
are connected to these pins.
CAN HIGH AND CAN LOW OUTPUTS
(CANH AND CANL)
The CAN High and CAN Low pins are the interfaces to the
CAN bus lines. They are controlled by TX input level, and the
state of CANH and CANL is reported through RX output.
VOLTAGE BATTERY (VBAT)
This pin is the voltage supply from the battery.
VOLTAGE REGULATOR THREE (V3)
This pin is a 10
switch to VBAT, which is used to supply
external contacts or relays.
相關PDF資料 |
PDF描述 |
|---|---|
| MC33388DR2 | IC TOLERANT CAN INT FAULT 14SOIC |
| PX0414 | CONN SMB JACK PNL MNT RG174 |
| PIC16LF1937-E/PT | IC PIC MCU FLASH 512KX14 44-TQFP |
| PIC16F1934-E/ML | IC PIC MCU FLASH 256KX7 44-QFN |
| V48C12M75B | CONVERTER MOD DC/DC 12V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC33389CDWR2 | 功能描述:網絡控制器與處理器 IC SYSTEM BASIC CHIPS RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| MC33389DDW | 功能描述:網絡控制器與處理器 IC SBC SOW28 RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| MC33389DDWR2 | 功能描述:網絡控制器與處理器 IC SBC SOW28 RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| MC33390D | 功能描述:IC TRANSCEIVER SER LINK 8-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| MC33390DR2 | 功能描述:IC TRANSCEIVER SER LINK 8-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。