- 您現在的位置：買賣IC網 > PDF目錄359133 > MC33793 (飛思卡爾半導體(中國)有限公司) Distributed System Interface (DSI) Sensor Interface(分布式系統接口（DSI）傳感器接口) PDF資料下載
參數資料
| 型號： | MC33793 |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | Distributed System Interface (DSI) Sensor Interface(分布式系統接口（DSI）傳感器接口) |
| 中文描述： | 分布式系統接口（DSI）傳感器接口（分布式系統接口（DSI）的傳感器接口） |
| 文件頁數： | 17/24頁 |
| 文件大小： | 640K |
| 代理商： | MC33793 |
MOTOROLA ANALOG INTEGRATED CIRCUIT DEVICE DATA
33793
17
I/O Control Command
This register controls the I/O ports. When the “DR” bits are
set, the corresponding I/O is enabled as an output. The “L” bit
settings control the level of the corresponding I/O if it is enabled
as an output. The format of this command is shown in
Table 11
.
I/O Control Response
The response indicates which I/O has been configured as
outputs and their current values.
The values returned will be the values programmed. The
values at the pins will not be the ones that were programmed if
the pin has been forced to the opposite state. The response
format is shown in
Table 12
. No response is generated if the
command address field was $0.
Request ID Command
This command will cause the device ID information to be
read from internal storage and returned to the master during the
response to the next message. The command format is found
in
Table 13
.
Table 11. I/O Control Command Format
Data
Address
Command
CRC
L3
L2
L1
L0
DR3
DR2
DR1
DR0
A3
A2
A1
A0
0
0
1
1
X3
X2
X1
X0
Legend
A[3:0] = Address bits.
DR[3:0] = I/O direction bits. 1 = Output. All bits are set to “0”
by reset/clear.
L[3:0] = Level to output on I/O if configured as output. All bits are set
to “0” by reset/clear
X[3:0] = Cyclic Redundancy Check (CRC). The CRC as calculated
by the master.
Table 12. I/O Control Response Format
High Byte
Low Byte
CRC
A3
A2
A1
A0
0
0
0
0
L3
L2
L1
L0
DR3
DR2
DR1
DR0
X3
X2
X1
X0
Legend
A[3:0] = Address bits.
DR[3:0] = I/O enabled as outputs (1 = enabled as output).
L[3:0] = Programmed values.
X[3:0] = Cyclic Redundancy Check (CRC). The CRC as calculated by
the slave.
Table 13. Request ID Command Format
Data
Address
Command
CRC
–
–
–
–
–
–
–
–
A3
A2
A1
A0
0
1
0
0
X3
X2
X1
X0
Legend
A[3:0] = Address bits. The address of the selected device.
An address value of “0000” is ignored by all devices.
X[3:0] = Cyclic Redundancy Check (CRC). The CRC as calculated
by the master.
F
Freescale Semiconductor, Inc.
Go to: www.freescale.com
n
.
相關PDF資料 |
PDF描述 |
|---|---|
| MC33794 | Electric Field Imaging Device(電場成像設備) |
| MC33880 | Configurable Octal Serial Switch with Serial Peripheral Interface I/O(可配置的8串行開關,帶串行外圍I/O口(SPI)) |
| MC33882 | Six-Output Low-Side Switch with SPI and Parallel Input Control(帶SPI和并口輸入控制的6輸出低端開關) |
| MC33883 | H-Bridge Gate Driver IC(H橋柵極驅動器) |
| MC33884 | Switch Monitor Interface(開關監控器接口) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC33793D | 功能描述:IC DSI SLAVE FOR R-SENSE 16-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| MC33793DR2 | 功能描述:IC DSI SLAVE FOR R-SENSE 16-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| MC33794DH | 功能描述:IC SENSOR ELECTRIC FIELD 44-HSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| MC33794DHR2 | 制造商:Rochester Electronics LLC 功能描述:OCCUPANT DETECT E-FIELD SENSOR FOR MCU SUPPORT - Bulk |
| MC33794DWB | 功能描述:IC SENSOR ELECTRIC FIELD 54-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。