- 您現在的位置：買賣IC網 > PDF目錄359133 > MC33993 (飛思卡爾半導體(中國)有限公司) Multiple Switch Detection Interface(多開關監測接口) PDF資料下載
參數資料
| 型號： | MC33993 |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | Multiple Switch Detection Interface(多開關監測接口) |
| 中文描述： | 多交換檢測接口（多開關監測接口） |
| 文件頁數： | 12/28頁 |
| 文件大?。?/td> | 820K |
| 代理商： | MC33993 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
33993/D
12
Go to: www.freescale.com
DEVICE OPERATION
Power Supply
The 33993 is designed to operate from 5.5 V to 40 V on the
V
PWR
pin. Characteristics are provided from 8.0 V to 16 V for
the device. Switch contact currents and the internal logic supply
are generated from the V
PWR
pin. The V
DD
supply pin is used to
set the SPI communication voltage levels, current source for the
SO driver, and pull-up current on
INT
and
CS
.
V
DD
supply may be removed from the device to reduce
quiescent current. If V
DD
is removed while the device is in
Normal mode, the device will remain in Normal mode. If V
DD
is
removed in Sleep mode, the device will remain in Sleep mode
until wake-up input is received (
WAKE
high to low, switch input
or interrupt timer expires).
Removing V
DD
from the device disables SPI communication
and will not allow the device to wake up from
INT
and
CS
pins.
Power-ON Reset (POR)
Applying V
PWR
to the device will cause a Power-ON Reset
and place the device in Normal mode.
Default settings from Power-ON Reset via V
PWR
or Reset
Command are as follows:
Programmable Switch – Set to Switch to Battery
All Inputs Set as Wake-Up
Wetting Current On (16 mA)
Wetting Current Timer On (20 ms)
All Inputs Tri-State
Analog Select 00000 (No Input Channel Selected)
Modes of Operation
The 33993 has two operating modes, Normal mode and
Sleep mode. A discussion on Normal mode begins below.
A discussion on Sleep mode begins on page 18.
Normal Mode
Normal mode may be entered by the following events:
Application of V
PWR
to the IC
Change-of-Switch State (when enabled)
Falling Edge of
WAKE
Falling Edge of
INT
(with V
DD
= 5.0 V and
WAKE
at
Logic [1])
Falling Edge of
CS
(with V
DD
= 5.0 V)
Interrupt Timer Expires
Only in Normal mode with V
DD
applied can the registers of the
33993 be programmed through the SPI.
The registers that may be programmed in Normal mode are
listed below. Further explanation of each register is provided in
subsequent paragraphs.
Programmable Switch Register
(
Settings Command
)
Wake-Up/Interrupt Register
(
Wake-Up/Interrupt
Command
)
Wetting Current Register
(
Metallic Command
)
Wetting Current Timer Register
(
Wetting Current Timer
Enable Command
)
Tri-State Register
(
Tri-State Command
)
Analog Select Register
(
Analog Command
)
Calibration of Timers
(
Calibration Command
)
Reset
(
Reset Command
)
Figure 4
, page 8, is a graphical description of the device
operation in Normal mode. Switch states are latched into the
input register on the falling edge of
CS
. The
INT
to the MCU is
cleared on the rising edge of CS. However,
INT
will not clear on
rising edge of
CS
if a switch has closed during SPI
communication (
CS
low). This prevents switch states from
being missed by the MCU.
Programmable Switch Register
Inputs SP0 to SP7 may be programmable for switch-to-
battery or switch-to-ground. These inputs types are defined
using the
settings command
(refer to
Table 1
). To set an SPn
input for switch-to-battery, a logic [1] for the appropriate bit must
be set. To set an SPn input for switch-to-ground, a logic [0] for
the appropriate bit must be set. The MCU may change or
update the Programmable Switch Register via software at any
time in Normal mode. Regardless of the setting, when the SPn
input switch is closed a logic [1] will be placed in the Serial
Output Response Register (refer to
Table 12
, page 17).
Table 1. Settings Command
Settings Command
Not used
Battery/Ground Select
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
0
0
0
0
0
0
0
1
X
X
X
X
X
X
X
X
sp7
sp6
sp5
sp4
sp3
sp2
sp1
sp0
F
Freescale Semiconductor, Inc.
For More Information On This Product,
n
.
相關PDF資料 |
PDF描述 |
|---|---|
| MC33997 | Switching Power Supply with Linear Regulators(帶線性穩壓器的開關電源) |
| MC33998 | Switching Power Supply with Linear Regulators(帶線性穩壓器的開關電源) |
| MC34017 | Telephone Tone Ringer(電話振鈴) |
| MC34063A | DC-DC CONVERTER CONTROL CIRCUITS |
| MC34063AB | DC-DC CONVERTER CONTROL CIRCUITS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC33993DWB | 功能描述:接口 - 專用 MSDI RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MC33993DWBR2 | 功能描述:接口 - 專用 MSDI RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MC33996EK | 功能描述:電源開關 IC - 配電 16LOW SIDE SW 1.2OHM RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| MC33996EKR2 | 功能描述:電源開關 IC - 配電 16LOW SIDE SW 1.2OHM RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| MC33997DW | 功能描述:IC SWITCH 3.3/5V SUPPLY 24-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。