- 您現在的位置：買賣IC網 > PDF目錄45247 > MC68HC05C12ACFN (MOTOROLA INC) 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQCC44 PDF資料下載
參數資料
| 型號： | MC68HC05C12ACFN |
| 廠商： | MOTOROLA INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQCC44 |
| 封裝： | PLASTIC, LCC-44 |
| 文件頁數： | 88/156頁 |
| 文件大小： | 756K |
| 代理商： | MC68HC05C12ACFN |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁當前第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁
Interrupts
Hardware Controlled Interrupt Sequence
MC68HC05C12A — Rev. 3.0
General Release Specification
MOTOROLA
Interrupts
37
NON-DISCLOSURE
AGREEMENT
REQUIRED
4.3 Hardware Controlled Interrupt Sequence
Three functions (RESET, STOP, and WAIT) are not in the strictest sense
interrupts; however, they are acted upon in a similar manner. Flowcharts
for hardware interrupts are shown in Figure 4-1.
1. RESET — A low input on the RESET input pin causes the program
to vector to its starting address, which is specified by the contents
of memory locations $3FFE and $3FFF. The I bit in the condition
code register is also set. Much of the MCU is configured to a
known state during this type of reset, as previously described in
2. STOP — The STOP instruction causes the oscillator to be turned
off and the processor to “sleep” until an external interrupt
(IRQ) or
reset occurs.
3. WAIT — The WAIT instruction causes all processor clocks to stop,
but leaves the timer clock running. This “rest” state of the
processor can be cleared by reset, an external interrupt (IRQ),
serial periferal interface, serial communications interface, or timer
interrupt. These individual interrupts have no special wait vectors.
4.4 Software Interrupt (SWI)
The software interrupt (SWI) is an executable instruction and a non-
maskable interrupt. It is executed regardless of the state of the I bit in the
CCR. If the I bit is 0 (interrupts enabled), SWI executes after interrupts
which were pending when the SWI was fetched but before interrupts
generated after the SWI was fetched. The interrupt service routine
address is specified by the contents of memory locations $3FFC and
$3FFD.
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HSC05C12AFN | 8-BIT, MROM, 4.1 MHz, MICROCONTROLLER, PQCC44 |
| MC68HC05C12ACP | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP40 |
| MC68HCL05C12AFB | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQFP44 |
| MC68HSC05C12AFB | 8-BIT, MROM, 4.1 MHz, MICROCONTROLLER, PQFP44 |
| MC68HSC05C12AB | 8-BIT, MROM, 4.1 MHz, MICROCONTROLLER, PDIP42 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HC05C12B | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:HCMOS MICROCONTROLLER UNITS |
| MC68HC05C12CP | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:HCMOS MICROCONTROLLER UNITS |
| MC68HC05C12P | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:HCMOS MICROCONTROLLER UNITS |
| MC68HC05C4 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:8-Bit Microcomputers |
| MC68HC05C8 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:PROGRAMMING REFRERENCE GUIDE |
發布緊急采購，3分鐘左右您將得到回復。