- 您現在的位置：買賣IC網 > PDF目錄45218 > MC68HC05C8AVFB (FREESCALE SEMICONDUCTOR INC) 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQFP44 PDF資料下載
參數資料
| 型號： | MC68HC05C8AVFB |
| 廠商： | FREESCALE SEMICONDUCTOR INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQFP44 |
| 封裝： | QFP-44 |
| 文件頁數： | 78/116頁 |
| 文件大?。?/td> | 781K |
| 代理商： | MC68HC05C8AVFB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁當前第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁
Serial Peripheral Interface (SPI)
MC68HC05C8A MC68HCL05C8A MC68HSC05C8A Data Sheet, Rev. 5.1
64
Freescale Semiconductor
10.5.2 Serial Peripheral Status Register
SPIF — SPI Transfer Complete Flag
The serial peripheral data transfer flag bit is set upon completion of data transfer between the
processor and external device. If SPIF goes high and if SPIE is set, a serial peripheral interrupt is
generated. Clearing the SPIF bit is accomplished by reading the SPSR (with SPIF set) followed by an
access of the SPDR. Unless SPSR is read (with SPIF set) first, attempts to write to SPDR are inhibited.
WCOL — Write Collision Bit
The write collision bit is set when an attempt is made to write to the serial peripheral data register while
data transfer is taking place. If CPHA is 0, a transfer is said to begin when SS goes low and the transfer
ends when SS goes high after eight clock cycles on SCK. When CPHA is 1, a transfer is said to begin
the first time SCK becomes active while SS is low. The transfer ends when the SPIF flag gets set.
Clearing the WCOL bit is accomplished by reading the SPSR (with WCOL set) followed by an access
to SPDR.
Bit 5 — Not implemented
This bit always reads as 0.
MODF — Mode Fault Flag
The mode fault flag indicates that there may have been a multi-master conflict for system control and
allows a proper exit from system operation to a reset or default system state. The MODF bit is normally
clear and is set only when the master device has its SS pin pulled low. Setting the MODF bit affects
the internal serial peripheral interface system in these ways:
An SPI interrupt is generated if SPIE = 1.
The SPE bit is cleared. This disables the SPI.
The MSTR bit is cleared, thus forcing the device into the slave mode.
Clearing the MODF bit is accomplished by reading the SPSR (with MODF set), followed by a write to
the SPCR. Control bits SPE and MSTR may be restored by user software to their original state after
the MODF bit has been cleared.
Bits 3–0 — Not Implemented
These bits always reads as 0.
Address: $000B
Bit 7
654321
Bit 0
Read:
SPIF
WCOL
0
MODF
0000
Write:
Reset
000000
U
= Unimplemented
U = Unaffected
Figure 10-5. SPI Status Register (SPSR)
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HSC05C8CFN | 8-BIT, MROM, 4.1 MHz, MICROCONTROLLER, PQCC44 |
| MC68HSC05C8CFB | 8-BIT, MROM, 4.1 MHz, MICROCONTROLLER, PQFP44 |
| MC68HC05C8APE | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP40 |
| MC68HC05C8AMB | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP42 |
| MC68HCL05C8AFN | 8-BIT, MROM, MICROCONTROLLER, PQCC44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HC05C9 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:TECHNICAL DATA |
| MC68HC05C9A | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Microcontrollers |
| MC68HC05C9AB | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Microcontrollers |
| MC68HC05C9AFB | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Microcontrollers |
| MC68HC05C9AFN | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Microcontrollers |
發布緊急采購，3分鐘左右您將得到回復。