- 您現在的位置：買賣IC網 > PDF目錄371048 > MC68HC11A1CFN2 (MOTOROLA INC) HCMOS Single-Chip Microcontroller PDF資料下載
參數資料
| 型號： | MC68HC11A1CFN2 |
| 廠商： | MOTOROLA INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | HCMOS Single-Chip Microcontroller |
| 中文描述： | 8-BIT, 2 MHz, MICROCONTROLLER, PQCC52 |
| 封裝： | PLASTIC, LCC-52 |
| 文件頁數： | 87/158頁 |
| 文件大?。?/td> | 776K |
| 代理商： | MC68HC11A1CFN2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁當前第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁
MC68HC11A8
TECHNICAL DATA
RESETS, INTERRUPTS, AND LOW POWER MODES
MOTOROLA
9-7
9
CSEL — A/D/EE Charge Pump Clock Source Select
This bit determines the clocking source for the on-chip A/D and EEPROM charge
pump. When this bit is zero, the MCU E clock drives the A/D system and the EEPROM
charge pump. When CSEL is one, on-chip separate R-C oscillators are enabled and
clock the systems at about 2 MHz. When running with an E clock below 1 MHz, CSEL
must be high to program or erase EEPROM. When operating below 750 kHz E clock
rate, CSEL should be high for A/D conversions. A delay of 10 milliseconds is required
after CSEL is turned on to allow the A/D system to stabilize.
IRQE — IRQ Edge/Level Sensitive
This bit may only be written under special circumstances as described above. When
this bit is clear, the IRQ pin is configured for level sensitive wired-OR operation (low
level) and when it is set, the IRQ pin is configured for edge-only sensitivity (falling edg-
es).
DLY — STOP Exit Turn-On Delay
This bit may only be written under special circumstances as described above. This bit
is set during reset and controls whether or not a relatively long turn-on delay will be
imposed before processing can resume after a STOP period. If an external clock
source is supplied this delay can be inhibited so that processing can resume within a
few cycles of a wake up from STOP mode. When DLY is set, a 4064 E clock cycle de-
lay is imposed to allow oscillator stabilization and when DLY is clear, this delay is by-
passed.
CME — Clock Monitor Enable
This control bit may be read or written at any time and controls whether or not the in-
ternal clock monitor circuit will trigger a reset sequence when a slow or absent system
clock is detected. When it is clear, the clock monitor circuit is disabled and when it is
set, the clock monitor circuit is enabled. Systems operating at or below 200 kHz should
not use the clock monitor function. Reset clears the CME bit.
Bit 2 — Not Implemented
This bit always reads zero.
CR1 and CR0 — COP Timer Rate Selects
These bits may only be written under special circumstances as described above. Re-
fer to
Table 9-1
for the relationship between CR1:CR0 and the COP timeout period.
9.2 Interrupts
When an external or internal (hardware) interrupt occurs, the interrupt is not serviced
until the current instruction being executed is completed. Until the current instruction
is complete, the interrupt is considered pending. After completion of current instruction
execution, unmasked interrupts may be serviced in accordance with an established
fixed hardware priority circuit; however, one l-bit related interrupt source may be dy-
namically elevated to the highest I bit priority position in the hierarchy (see
9.2.5 High-
est Priority I Interrupt Register (HPRIO)
).
Seventeen hardware interrupts and one software interrupt (excluding reset type inter-
rupts) can be generated from all of the possible sources. The interrupts can be divided
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HCP11A1CFN2 | HCMOS Single-Chip Microcontroller |
| MC68HCP11A1CFN3 | HCMOS Single-Chip Microcontroller |
| MC68HCP11A1CP2 | HCMOS Single-Chip Microcontroller |
| MC68HCP11A1CP3 | HCMOS Single-Chip Microcontroller |
| MC68HCP11A1MFN2 | HCMOS Single-Chip Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HC11A1CFN3 | 制造商:Rochester Electronics LLC 功能描述: |
| MC68HC11A1CFNE3 | 功能描述:8位微控制器 -MCU 8B MCU 256RAM A/D EE RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MC68HC11A1CFNE3 | 制造商:Freescale Semiconductor 功能描述:8-BIT MICROCONTROLLER IC |
| MC68HC11A1CFNE3R | 功能描述:8位微控制器 -MCU 8B MCU 256RAM A/D EE RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MC68HC11A1CFU2 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:HCMOS Single-Chip Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。