參數資料
型號: MC68HC11A1MFN2
廠商: FREESCALE SEMICONDUCTOR INC
元件分類: 微控制器/微處理器
英文描述: 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PQCC52
封裝: PLASTIC, LCC-52
文件頁數: 73/158頁
文件大?。?/td> 3803K
代理商: MC68HC11A1MFN2
SIGNAL DESCRIPTIONS AND OPERATING MODES
MOTOROLA
TECHNICAL DATA
2-5
2
2.1.11.1 Port A
Port A may be configured for: three input capture functions (IC1, IC2, IC3), four output
compare functions (OC2, OC3, OC4, OC5), and either a pulse accumulator input (PAI)
or a fifth output compare function (OC1). Refer to 8.1 Programmable Timer for addi-
tional information.
Any port A pin that is not used for its alternate timer function may be used as a general-
purpose input or output line.
2.1.11.2 Port B
While in single-chip operating modes, all of the port B pins are general-purpose output
pins. During MCU reads of this port, the level sensed at the input side of the port B
output drivers is read. Port B may also be used in a simple strobed output mode where
an output pulse appears at the STRB signal each time data is written to port B.
When in expanded multiplexed operating modes, all of the port B pins act as high order
address output signals. During each MCU cycle, bits 8 through 15 of the address are
output on the PB0-PB7 lines respectively.
2.1.11.3 Port C
While in single-chip operating modes, all port C pins are general-purpose input/output
pins. Port C inputs can be latched by providing an input transition to the STRA signal.
Port C may also be used in full handshake modes of parallel l/O where the STRA input
and STRB output act as handshake control lines.
When in expanded multiplexed operating modes, all port C pins are configured as mul-
tiplexed address/data signals. During the address portion of each MCU cycle, bits 0
through 7 of the address are output on the PC0-PC7 lines. During the data portion of
each MCU cycle (E high), pins 0 through 7 are bidirectional data signals (D0-D7). The
direction of data at the port C pins is indicated by the R/W signal.
2.1.11.4 Port D
Port D pins 0-5 may be used for general-purpose l/O signals. Port D pins alternately
serve as the serial communications interface (SCI) and serial peripheral interface
(SPI) signals when those subsystems are enabled.
Pin PD0 is the receive data input (RxD) signal for the serial communication interface
(SCI).
Pin PD1 is the transmit data output (TxD) signal for the SCI.
Pins PD2 through PD5 are dedicated to the SPI. PD2 is the master-in-slave-out (MI-
SO) signal. PD3 is the master-out-slave-in (MOSI) signal. PD4 is the serial clock
(SCK) signal and PD5 is the slave select (SS) input.
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
相關PDF資料
PDF描述
MC68HC11A1MFU2 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PQFP64
MC68HC11A8BMP2 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PDIP48
MC68HCP11A1VP2 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PDIP48
MC68HC11A8P1 8-BIT, MROM, MICROCONTROLLER, PDIP48
MC68HC11A1MP 8-BIT, EEPROM, 2 MHz, MICROCONTROLLER, PDIP48
相關代理商/技術參數
參數描述
MC68HC11A1MFNE 功能描述:8位微控制器 -MCU 8B MCU 256RAM A/D EE RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HC11A1MFNER 功能描述:8位微控制器 -MCU 8B MCU 256RAM A/D EE RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HC11A1MFU2 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:HCMOS Single-Chip Microcontroller
MC68HC11A1MP 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:8-Bit Microcontrollers
MC68HC11A1MP2 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:HCMOS Single-Chip Microcontroller