參數資料
型號: MC68HC11F1MFN3
廠商: FREESCALE SEMICONDUCTOR INC
元件分類: 微控制器/微處理器
英文描述: 8-BIT, EEPROM, 3 MHz, MICROCONTROLLER, PQCC68
封裝: PLASTIC, LCC-68
文件頁數: 125/162頁
文件大?。?/td> 4554K
代理商: MC68HC11F1MFN3
RESETS AND INTERRUPTS
MOTOROLA
TECHNICAL DATA
5-3
Semiconductor wafer processing causes variations of the RC time-out values between
individual devices. An E-clock frequency below 10 kHz is detected as a clock monitor
error. An E-clock frequency of 200 kHz or more prevents clock monitor errors. Using
the clock monitor function when the E-clock is below 200 kHz is not recommended.
Special considerations are needed when a STOP instruction is executed and the clock
monitor is enabled. Because the STOP function causes the clocks to be halted, the
clock monitor function generates a reset sequence if it is enabled at the time the STOP
mode was initiated. Before executing a STOP instruction, clear to zero the CME bit in
the OPTION register to disable the clock monitor. After recovery from STOP, set the
CME bit to logic one to enable the clock monitor.
5.1.5 OPTION Register
*Can be written only once in first 64 cycles out of reset in normal modes, or at any time in special modes.
ADPU — Analog-to-Digital Converter Power-Up
CSEL — Clock Select
IRQE — Configure IRQ for Edge-Sensitive Only Operation
0 = Low level sensitive operation.
1 = Falling edge sensitive only operation.
DLY — Enable Oscillator Start-up Delay
0 = The oscillator start-up delay coming out of STOP is bypassed and the MCU re-
sumes processing within about four bus cycles.
1 = A delay of approximately 4000 E-clock cycles is imposed as the MCU is started
up from the STOP power-saving mode.
CME — Clock Monitor Enable
This control bit can be read or written at any time and controls whether or not the in-
ternal clock monitor circuit triggers a reset sequence when the system clock is slow or
absent. When it is clear, the clock monitor circuit is disabled, and when it is set, the
clock monitor circuit is enabled. Reset clears the CME bit.
FCME — Force Clock Monitor Enable
To use STOP mode, the FCME bit must equal zero.
0 = Clock monitor follows the state of the CME bit.
1 = Clock monitor circuit is enabled until next reset
OPTION — System Configuration Options
$1039
Bit 7
654321
Bit 0
ADPU
CSEL
IRQE*
DLY*
CME
FCME*
CR1*
CR0*
RESET:
0001000
0
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
相關PDF資料
PDF描述
MC68HC11K3CFU2 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PQFP80
MC68HC11K3CFU4 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP80
MC68HC11K3VFU3 8-BIT, MROM, 3 MHz, MICROCONTROLLER, PQFP80
MC68HC711K4CFS4 8-BIT, UVPROM, 4 MHz, MICROCONTROLLER, CQCC84
MC68L11K0FU3 8-BIT, 3 MHz, MICROCONTROLLER, PQFP80
相關代理商/技術參數
參數描述
MC68HC11F1MFN4 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Technical Summary 8-Bit Microcontroller
MC68HC11F1MFU 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers
MC68HC11F1MFU1 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers
MC68HC11F1MFU3 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers
MC68HC11F1MFU4 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers