- 您現在的位置：買賣IC網 > PDF目錄299472 > MC68HC11FC0CFU5 (MOTOROLA INC) Technical Summary 8-Bit Microcontroller PDF資料下載
參數資料
| 型號： | MC68HC11FC0CFU5 |
| 廠商： | MOTOROLA INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Technical Summary 8-Bit Microcontroller |
| 中文描述： | 8-BIT, 6 MHz, MICROCONTROLLER, PQFP64 |
| 封裝： | QFP-64 |
| 文件頁數： | 16/74頁 |
| 文件大小： | 513K |
| 代理商： | MC68HC11FC0CFU5 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁
MC68HC11F1/FC0
MOTOROLA
MC68HC11FTS/D
23
CWOM — Port C Wired-OR Mode Option
Refer to 7.8 Parallel I/O Registers, page 37.
CLK4X — 4XCLK Output Enable
This bit can only be written once after reset in all modes.
0 = 4XOUT clock output is disabled
1 = Buffered oscillator is driven on the 4XOUT clock output
LIRDV — Load Instruction Register Driven
In order to detect consecutive instructions in a high-speed application, LIR can be driven high for one
quarter of an E-clock cycle during each instruction fetch.
0 = LIR signal is not driven high.
1 = LIR signal is driven high.
Bits 3, 1, 0 — Not implemented. Reads always return zero and writes have no effect.
SPRBYP — See 10.2 SPI Registers, page 52.
*Can be written only once in first 64 cycles out of reset in normal modes, or at any time in special modes.
ADPU — A/D Power-Up
This bit is implemented on the MC68HC11F1 only. On the MC68HC11FC0, reads always return zero
and writes have no effect.
0 = A/D system disabled
1 = A/D system enabled
CSEL — Clock Select
This bit is implemented on the MC68HC11F1 only. On the MC68HC11FC0, reads always return zero
and writes have no effect.
0 = A/D and EEPROM use system E clock
1 = A/D and EEPROM use internal RC clock
IRQE — IRQ Select Edge Sensitive Only
0 = Low level recognition
1 = Falling edge recognition
DLY — Enable Oscillator Start-Up Delay on Exit from STOP
0 = No stabilization delay on exit from STOP
1 = Stabilization delay of 4064 E-clock cycles is enabled on exit from STOP
CME — Clock Monitor Enable
0 = Clock monitor disabled; slow clocks can be used
1 = Slow or stopped clocks cause clock failure reset
FCME — Force Clock Monitor Enable
0 = Clock monitor circuit follows the state of the CME bit
1 = Clock monitor circuit is enabled until the next reset
In order to use both STOP and the clock monitor, the CME bit should be written to zero prior to executing
a STOP instruction and rewritten to one after recovery from STOP. FCME should be kept cleared if the
user intends to use the STOP instruction.
CR[1:0] — COP Timer Rate Select
Refer to 5.2 Reset and Interrupt Registers, page 27.
OPTION — System Configuration Options
$x039
Bit 7
6
5
4
3
2
1
Bit 0
ADPU
CSEL
IRQE*
DLY*
CME
FCME*
CR1*
CR0*
RESET:
0
1
0
相關PDF資料 |
PDF描述 |
|---|---|
| MC68L11FC0PU3 | Technical Summary 8-Bit Microcontroller |
| MC68L11FC0PU4 | Technical Summary 8-Bit Microcontroller |
| MC74A6-3.3T | DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 3Cel, RECTANGULAR, THROUGH HOLE MOUNT |
| MC74F37DR2 | F/FAST SERIES, QUAD 2-INPUT NAND GATE, PDSO14 |
| MC74HC4851ADR2 | 8-CHANNEL, SGL ENDED MULTIPLEXER, PDSO16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HC11FC0CPU4 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Technical Summary 8-Bit Microcontroller |
| MC68HC11FC0CPU5 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Technical Summary 8-Bit Microcontroller |
| MC68HC11FC0FU6 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Technical Summary 8-Bit Microcontroller |
| MC68HC11FC0PU6 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Technical Summary 8-Bit Microcontroller |
| MC68HC11G5 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:High-density Complementary Metal Oxide Semiconductor (HCMOS) Microcontroller Unit |
發布緊急采購，3分鐘左右您將得到回復。