參數資料
型號： MC68HCL05C12AB
廠商： MOTOROLA INC
元件分類： 微控制器/微處理器
英文描述： 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP42
封裝： PLASTIC, SDIP-42
文件頁數： 88/156頁
文件大?。?/td> 756K
代理商： MC68HCL05C12AB
Interrupts
Hardware Controlled Interrupt Sequence
MC68HC05C12A — Rev. 3.0
General Release Specification
MOTOROLA
Interrupts
37
NON-DISCLOSURE
AGREEMENT
REQUIRED
4.3 Hardware Controlled Interrupt Sequence
Three functions (RESET, STOP, and WAIT) are not in the strictest sense
interrupts; however, they are acted upon in a similar manner. Flowcharts
for hardware interrupts are shown in Figure 4-1.
1. RESET — A low input on the RESET input pin causes the program
to vector to its starting address, which is specified by the contents
of memory locations $3FFE and $3FFF. The I bit in the condition
code register is also set. Much of the MCU is configured to a
known state during this type of reset, as previously described in
2. STOP — The STOP instruction causes the oscillator to be turned
off and the processor to “sleep” until an external interrupt
(IRQ) or
reset occurs.
3. WAIT — The WAIT instruction causes all processor clocks to stop,
but leaves the timer clock running. This “rest” state of the
processor can be cleared by reset, an external interrupt (IRQ),
serial periferal interface, serial communications interface, or timer
interrupt. These individual interrupts have no special wait vectors.
4.4 Software Interrupt (SWI)
The software interrupt (SWI) is an executable instruction and a non-
maskable interrupt. It is executed regardless of the state of the I bit in the
CCR. If the I bit is 0 (interrupts enabled), SWI executes after interrupts
which were pending when the SWI was fetched but before interrupts
generated after the SWI was fetched. The interrupt service routine
address is specified by the contents of memory locations $3FFC and
$3FFD.
相關PDF資料
PDF描述
MC68HSC05C12CFB 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP44
MC68HSC05C12B 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PDIP42
MC68HCL05C12FB 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQFP44
MC68HSC05C12CFN 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQCC44
MC68HCL05C12B 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP42
相關代理商/技術參數
參數描述
MC68HCP11A1CFN3 功能描述:8位微控制器 -MCU 8-bit HCMOS single chip MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HCP11A1FN 制造商:MOTORALA 功能描述:
MC68HCP11E0CP2 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC68HCP11E0FN 功能描述:MICROCONTROLLER MCU 8ADC 3MHC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:HC11 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323
MC68HCP11E0FNE 功能描述:8位微控制器 -MCU 8B MCU 512RAM COP A/D RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*