- 您現在的位置：買賣IC網 > PDF目錄4044 > MC7447AHX1000LB (Freescale Semiconductor)IC MPU RISC 32BIT 360-FCCBGA PDF資料下載
參數資料
| 型號： | MC7447AHX1000LB |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 9/56頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MPU RISC 32BIT 360-FCCBGA |
| 標準包裝： | 44 |
| 系列： | MPC74xx |
| 處理器類型： | 32-位 MPC74xx PowerPC |
| 速度： | 1.0GHz |
| 電壓： | 1.3V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 360-BCBGA，F(xiàn)CCBGA |
| 供應商設備封裝： | 360-FCCBGA（25x25） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
MPC7447A RISC Microprocessor Hardware Specifications, Rev. 5
Freescale Semiconductor
17
Electrical and Thermal Characteristics
Figure 4 provides the AC test load for the MPC7447A.
Figure 4. AC Test Load
SYSCLK to ARTRY/SHD0/SHD1 high impedance after
precharge
tKHARPZ
—2
tSYSCLK 3, 5, 6, 7
Notes:
1. All input specifications are measured from the midpoint of the signal in question to the midpoint of the rising edge
of the input SYSCLK. All output specifications are measured from the midpoint of the rising edge of SYSCLK to
the midpoint of the signal in question. All output timings assume a purely resistive 50-
Ω load (see Figure 4). Input
and output timings are measured at the pin; time-of-flight delays must be added for trace lengths, vias, and
connectors in the system.
2. The symbology used for timing specifications herein follows the pattern of t(signal)(state)(reference)(state) for inputs
and t(reference)(state)(signal)(state) for outputs. For example, tIVKH symbolizes the time input signals (I) reach the valid
state (V) relative to the SYSCLK reference (K) going to the high (H) state or input setup time. And tKHOV
symbolizes the time from SYSCLK(K) going high (H) until outputs (O) are valid (V) or output valid time. Input hold
time can be read as the time that the input signal (I) went invalid (X) with respect to the rising clock edge (KH)
(note the position of the reference and its state for inputs) and output hold time can be read as the time from the
rising edge (KH) until the output went invalid (OX).
3. tsysclk is the period of the external clock (SYSCLK) in ns. The numbers given in the table must be multiplied by
the period of SYSCLK to compute the actual time duration (in ns) of the parameter in question.
4. According to the bus protocol, TS is driven only by the currently active bus master. It is asserted low and
precharged high before returning to high impedance, as shown in Figure 6. The nominal precharge width for TS
is 0.5
× tSYSCLK, that is, less than the minimum tSYSCLK period, to ensure that another master asserting TS on
the following clock will not contend with the precharge. Output valid and output hold timing is tested for the signal
asserted. Output valid time is tested for precharge.The high-impedance behavior is guaranteed by design.
5. Guaranteed by design and not tested.
6. According to the bus protocol, ARTRY can be driven by multiple bus masters through the clock period immediately
following AACK. Bus contention is not an issue because any master asserting ARTRY will be driving it low. Any
master asserting it low in the first clock following AACK will then go to high impedance for 1 clock before
precharging it high during the second cycle after the assertion of AACK. The nominal precharge width for ARTRY
is 1.0 tSYSCLK; that is, it should be high impedance as shown in Figure 6 before the first opportunity for another
master to assert ARTRY. Output valid and output hold timing is tested for the signal asserted.The high-impedance
behavior is guaranteed by design.
7. According to the MPX bus protocol, SHD0 and SHD1 can be driven by multiple bus masters beginning the cycle
of TS. Timing is the same as ARTRY, that is, the signal is high impedance for a fraction of a cycle, then negated
for up to an entire cycle (crossing a bus cycle boundary) before being three-stated again. The nominal precharge
width for SHD0 and SHD1 is 1.0 tSYSCLK. The edges of the precharge vary depending on the programmed ratio
of core to bus (PLL configurations).
8. BMODE[0:1] and BVSEL are mode select inputs and are sampled before and after HRESET negation. These
parameters represent the input setup and hold times for each sample. These values are guaranteed by design
and not tested. These inputs must remain stable after the second sample. See Figure 5 for sample timing.
Table 9. Processor Bus AC Timing Specifications1 (continued)
At recommended operating conditions. See Table 4.
Parameter
Symbol 2
All Speed Grades
Unit
Notes
Min
Max
Output
Z0 = 50 Ω
OVDD/2
RL = 50 Ω
相關PDF資料 |
PDF描述 |
|---|---|
| MPC8535BVTATHA | MCU PWRQUICC II 1250MHZ 783-PBGA |
| XC4036XL-3HQ304C | IC FPGA C-TEMP 3.3V 3SPD 304HQFP |
| 65801-123LF | CLINCHER RECEPTACLE ASSY TIN |
| 65801-121LF | CLINCHER RECEPTACLE ASSY TIN |
| MPC8543EPXANGB | MPU POWERQUICC III 783-PBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC7447AHX1000NB | 功能描述:微處理器 - MPU APOLO7PM RV1.1 1.1V 105C RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324 |
| MC7447AHX1000NBR | 制造商:Freescale Semiconductor 功能描述:MPU MPC74XX RISC 32BIT 0.13UM 1GHZ 1.8V/2.5V 360FCCBGA - Tape and Reel |
| MC7447AHX1000PC | 制造商:Freescale Semiconductor 功能描述:MPU MPC74XX RISC 32BIT 0.13UM 1GHZ 1.8V/2.5V 360FCCBGA - Bulk |
| MC7447AHX1167NB | 功能描述:微處理器 - MPU APOLO7PM RV1.1 1.1V 105C RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324 |
| MC7447AHX1167NB | 制造商:Freescale Semiconductor 功能描述:IC 32-BIT MPU 1.167GHZ 360-FCCBGA |
發布緊急采購，3分鐘左右您將得到回復。