參數資料
型號： MCHC11F1CFNE2
廠商： Freescale Semiconductor
文件頁數： 94/158頁
文件大小： 0K
描述： IC MCU 512 EEPROM 68-PLCC
標準包裝： 18
系列： HC11
核心處理器： HC11
芯體尺寸： 8-位
速度： 2MHz
連通性： SCI，SPI
外圍設備： POR，WDT
輸入/輸出數： 30
程序存儲器類型： ROMless
EEPROM 大?。?/td> 512 x 8
RAM 容量： 1K x 8
電壓 - 電源 (Vcc/Vdd)： 4.75 V ~ 5.25 V
數據轉換器： A/D 8x8b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 68-LCC（J 形引線）
包裝： 管件
OPERATING MODES AND ON-CHIP MEMORY
MC68HC11F1
4-2
TECHNICAL DATA
The bootstrap ROM contains a small program which initializes the SCI and allows the
user to download a program of up to 1024 bytes into on-chip RAM. After a four-char-
acter delay, or after receiving the character for address $03FF, control passes to the
loaded program at $0000. An external pull-up resistor is required when using the SCI
transmitter pin (TxD) because port D pins are configured for wired-OR operation by
the bootloader. In bootstrap mode, the interrupt vectors point to RAM. This allows the
use of interrupts through a jump table. Refer to Freescale application note AN1060,
M68HC11 Bootstrap Mode.
4.2 On-Chip Memory
The MC68HC11F1 contains 1024 bytes of on-chip RAM and 512 bytes of EEPROM.
The bootloader ROM occupies 256 bytes. The CONFIG register is implemented as a
separate EEPROM byte.
4.2.1 Mapping Allocations
Memory locations for on-chip resources are the same for both expanded and single-
chip modes. The 96-byte register block originates at $1000 after reset and can be
placed at any other 4-Kbyte boundary ($x000) after reset by writing an appropriate val-
ue to the INIT register. Refer to Figure 4-1, which illustrates the memory map.
The on-board 1024-byte RAM is initially located at $0000 after reset. If RAM and reg-
isters are both mapped to the same 4-Kbyte boundary, the first 96 bytes of RAM are
inaccessible (registers have higher priority). Remapping is accomplished by writing
appropriate values to the INIT register.
The 512-byte EEPROM array is initially located at $FE00 after reset when EEPROM
is enabled in the memory map by the CONFIG register. In expanded and special test
modes EEPROM can be placed at any other 4-Kbyte boundary ($xE00) by program-
ming bits EE[3:0] in the CONFIG register to an appropriate value. In single-chip and
bootstrap modes the EEPROM is forced on and cannot be remapped.
In special bootstrap mode, a bootloader ROM is enabled at locations $BF00–$BFFF.
The vectors for special bootstrap mode are contained in the bootloader program. The
boot ROM fills 256 bytes of the memory map even though not all locations are used.
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
相關PDF資料
PDF描述
1-2064752-3 SHUTTER ADDPT DUP LC FLANGELESS
2064752-3 SHUTTER ADDPT DUP LC FLANGELESS
2064752-2 SHUTTER ADDPT DUP LC FLANGELESS
2064752-1 SHUTTER ADDPT DUP LC FLANGELESS
VI-B4M-CU-F2 CONVERTER MOD DC/DC 10V 200W
相關代理商/技術參數
參數描述
MCHC11F1CFNE2 制造商:Freescale Semiconductor 功能描述:8-Bit Microcontroller IC
MCHC11F1CFNE2R 功能描述:8位微控制器 -MCU 8B MCU 1KRAM 512EE RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MCHC11F1CFNE3 功能描述:8位微控制器 -MCU 8B MCU 1KRAM 512EE RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MCHC11F1CFNE3 制造商:Freescale Semiconductor 功能描述:8-Bit Microcontroller IC
MCHC11F1CFNE3R 功能描述:8位微控制器 -MCU 8B MCU 1KRAM 512EE RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*