參數資料
型號: MCOTS-C-48-24-HP-D-M
廠商: SYNQOR INC
元件分類: 電源模塊
英文描述: 1-OUTPUT 252 W DC-DC REG PWR SUPPLY MODULE
封裝: HALF BRICK PACKAGE-8
文件頁數: 14/15頁
文件大?。?/td> 2624K
代理商: MCOTS-C-48-24-HP-D-M
Technical Specification
Product # MCOTS-C-48-24-HP
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0005424 Rev. C
05/07/10
Page 8
MCOTS-C-48-24-HP
Output: 24V
Current: 10.5A
Figure A: Various circuits for driving the ON/OFF pin.
Figure B: Internal ON/OFF pin circuitry
TTL
5V
50k
ON/OFF
Vin(_)
100pF
Open Collector Enable Circuit
Remote Enable Circuit
Direct Logic Drive
Negative Logic
(Permanently
Enabled)
ON/OFF
Vin(_
)
ON/OFF
Vin(_
)
ON/OFF
5V
TTL/
CMOS
Vin(_
)
Vin(_
)
OPEN
This Mil-COTS converter series uses a two-stage power
conversion topology. The first stage is a buck-converter that
keeps the output voltage constant over variations in line, load,
and temperature. The second stage uses a transformer to
provide the functions of input/output isolation and voltage
step-up or step-down to achieve the output voltage required.
Both the first stage and the second stage switch at a fixed
frequency for predictable EMI performance. Rectification of the
transformer’s output is accomplished with synchronous rectifiers.
These devices, which are MOSFETs with a very low on-state
resistance, dissipate far less energy than Schottky diodes. This
is the primary reason that the converter has such high efficiency,
even at very low output voltages and very high output currents.
These converter are offered totally encased to withstand
harsh environments and thermally demanding applications.
Dissipation throughout the converter is so low that
it does not require a heatsink for operation in many
applications; however, adding a heatsink provides improved
thermal derating performance in extreme situations.
This series of converters use the industry standard footprint
and pin-out configuration.
BASIC OPERATION AND FEATURES
CONTROL FEATURES
REMOTE ON/OFF (Pin 2): The ON/OFF input, Pin 2, permits
the user to control when the converter is on or off. This input
is referenced to the return terminal of the input bus, Vin(-).
The ON/OFF signal is active low (meaning that a low turns the
converter on). Figure A details four possible circuits for driving
the ON/OFF pin. Figure B is a detailed look of the internal ON/
OFF circuitry.
REMOTE SENSE(+) (Pins 7 and 5): The SENSE(+) inputs
correct for voltage drops along the conductors that connect the
converter’s output pins to the load.
Pin 7 should be connected to Vout(+) and Pin 5 should be
connected to Vout(-) at the point on the board where regulation
is desired. A remote connection at the load can adjust for a
voltage drop only as large as that specified in this datasheet,
that is
[Vout(+) - Vout(-)] [Vsense(+) - Vsense(-)] <
Sense Range % x Vout
Pins 7 and 5 must be connected for proper regulation of
the output voltage. If these connections are not made, the
converter will deliver an output voltage that is slightly higher
than its specified value.
Note: the output over-voltage protection circuit senses the
voltage across the output (pins 8 and 4) to determine when
it should trigger, not the voltage across the converter’s sense
leads (pins 7 and 5). Therefore, the resistive drop on the board
should be small enough so that output OVP does not trigger,
even during load transients.
相關PDF資料
PDF描述
MCP100-460HI/TO 1-CHANNEL POWER SUPPLY SUPPORT CKT, PBCY3
MCP111T-300TT Micropower Voltage Detector
MCP111T-315E Micropower Voltage Detector
MCP111T-315LB Micropower Voltage Detector
MCP111T-315TT Micropower Voltage Detector
相關代理商/技術參數
參數描述
MCOTS-F-28-P-QT 制造商:SYNQOR 制造商全稱:SYNQOR 功能描述:MILITARY COTS EMI FILTER
MCOTS-F-28-P-QT-F-S 制造商:SYNQOR 功能描述:EMI FILTER
MCOTS-F-28-P-QT-N-S 制造商:SYNQOR 功能描述:DC TO DC CONVERTER MODULE
MCOTS-F-28-T-HT-F-S 制造商:SYNQOR 功能描述:EMI FILTER
MCOTS-F-28-T-HT-N-S 制造商:SYNQOR 功能描述:EMI FILTER