- 您現在的位置：買賣IC網 > PDF目錄383586 > MCP1725 (Microchip Technology Inc.) 500 mA, Low Voltage, Low Quiescent Current LDO Regulator PDF資料下載
參數資料
| 型號： | MCP1725 |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | 500 mA, Low Voltage, Low Quiescent Current LDO Regulator |
| 中文描述： | 500毫安，低電壓，低靜態電流LDO穩壓器 |
| 文件頁數： | 17/32頁 |
| 文件大?。?/td> | 1000K |
| 代理商： | MCP1725 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
2006 Microchip Technology Inc.
DS22026A-page 17
MCP1725
4.4
Input Capacitor
Low input source impedance is necessary for the LDO
output to operate properly. When operating from
batteries, or in applications with long lead length
(> 10 inches) between the input source and the LDO,
some input capacitance is recommended. A minimum
of 1.0 μF to 4.7 μF is recommended for most
applications.
For applications that have output step load
requirements, the input capacitance of the LDO is very
important. The input capacitance provides the LDO
with a good local low-impedance source to pull the
transient currents from in order to respond quickly to
the output load step. For good step response
performance, the input capacitor should be of
equivalent (or higher) value than the output capacitor.
The capacitor should be placed as close to the input of
the LDO as is practical. Larger input capacitors will also
help reduce any high-frequency noise on the input and
output of the LDO and reduce the effects of any
inductance that exists between the input source
voltage and the input capacitance of the LDO.
4.5
Power Good Output (PWRGD)
The PWRGD output is used to indicate when the output
voltage of the LDO is within 92% (typical value, see
Section 1.0 “Electrical Characteristics”
for Minimum
and Maximum specifications) of its nominal regulation
value.
As the output voltage of the LDO rises, the PWRGD
output will be held low until the output voltage has
exceeded the power good threshold plus the hysteresis
value. Once this threshold has been exceeded, the
power good time delay is started (shown as T
PG
in
Section 1.0 “Electrical Characteristics”
). The power
good time delay is adjustable via the C
DELAY
pin of the
LDO (see
Section 4.6 “C
DELAY
Input”
). By placing a
capacitor from the C
DELAY
pin to ground, the power
good time delay can be adjusted from 200 μs (no
capacitance) to 300 ms (0.1 μF capacitor). After the
time delay period, the PWRGD output will go high,
indicating that the output voltage is stable and within
regulation limits.
If the output voltage of the LDO falls below the power
good threshold, the power good output will transition
low. The power good circuitry has a 170 μs delay when
detecting a falling output voltage, which helps to
increase noise immunity of the power good output and
avoid false triggering of the power good output during
fast output transients. See
Figure 4-2
for power good
timing characteristics.
When the LDO is put into Shutdown mode using the
SHDN input, the power good output is pulled low
immediately, indicating that the output voltage will be
out of regulation. The timing diagram for the power
good output when using the shutdown input is shown in
Figure 4-3
.
The power good output is an open-drain output that can
be pulled up to any voltage that is equal to or less than
the LDO input voltage. This output is capable of sinking
1.2 mA (V
PWRGD
< 0.4V maximum).
FIGURE 4-2:
Power Good Timing.
FIGURE 4-3:
Shutdown.
Power Good Timing from
T
PG
T
VDET_PWRGD
V
PWRGD_TH
V
OUT
PWRGD
V
OL
V
OH
V
IN
SHDN
V
OUT
30 μs
70 μs
T
OR
PWRGD
T
PG
相關PDF資料 |
PDF描述 |
|---|---|
| MCP1726 | 1A, Low Voltage, Low Quiescent Current LDO Regulator |
| MCP1727 | 1.5A, Low Voltage, Low Quiescent Current LDO Regulator |
| MCP1801 | 150 mA, High PSRR, Low Quiescent Current LDO |
| MCP1802 | 300 mA, High PSRR, Low Quiescent Current LDO |
| MCP1827T-1202EAB | 1.5A, Low Voltage, Low Quiescent Current LDO Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP1725-0802E/MC | 功能描述:低壓差穩壓器 - LDO 500mA CMOS LDO Vout=0.8V RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MCP1725-0802E/SN | 功能描述:低壓差穩壓器 - LDO 500mA CMOS LDO Vout=0.8V RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MCP1725-1202E/MC | 功能描述:低壓差穩壓器 - LDO 500mA CMOS LDO Vout=1.2V RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MCP1725-1202E/SN | 功能描述:低壓差穩壓器 - LDO 500mA CMOS LDO Vout=1.2V RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MCP1725-1802E/MC | 功能描述:低壓差穩壓器 - LDO 500mA CMOS LDO Vout=1.8V RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
發布緊急采購，3分鐘左右您將得到回復。