參數資料
型號： MCP2140AT-I/SS
廠商： Microchip Technology
文件頁數： 64/66頁
文件大小： 0K
描述： IC IRDA CONTROLLR DTE/DCE 20SSOP
標準包裝： 1,600
控制器類型： IRDA 標準協議棧控制器
接口： UART
電源電壓： 2 V ~ 5.5 V
電流 - 電源： 2.2mA
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 20-SSOP（0.209"，5.30mm 寬）
供應商設備封裝： 20-SSOP
包裝： 帶卷 (TR)
配用： MCP2140DM-TMPSNS-ND - BOARD DEMO FOR MCP2140
其它名稱： MCP2140AT-I/SSTR
2007-2011 Microchip Technology Inc.
DS22050B-page 7
MCP2140A
2.0
DEVICE OPERATION
The MCP2140A serial interface and IR baud rates are
fixed at 9600 baud, given a 3.6864 MHz device clock.
2.1
Power-Up
Any time the device is powered up (Parameter D003),
the Power-Up Timer delay (Parameter 33) occurs, fol-
lowed by an Oscillator Start-up Timer (OST) delay
(Parameter 32). Once these delays are complete, com-
munication with the device may be initiated. This com-
munication is from both the infrared transceiver’s side
and the controller’s UART interface.
2.1.1
POWER-ON AND BROWN-OUT
CONDITIONS
When any state machine is operated outside of its’
specified operating conditions, undesired operation
may occur. Application validation should be done to
determine when the system exits from either a Power-
On or a Brown-Out conditions if the MCP2140A
requires the use of an external voltage supervisory
circuit to ensure proper system operation.
2.2
Device Reset
The MCP2140A is forced into the Reset state when the
RESET pin is in the low state. Once the RESET pin is
brought to a high state, the device Reset sequence
occurs. Once the sequence completes, functional
operation begins.
2.3
Device Clocks
The MCP2140A requires a clock source to operate.
This clock source is used to establish the device timing,
including the device “Bit Clock”.
2.3.1
CLOCK SOURCE
The clock source can be supplied by one of the
following:
Crystal
Resonator
External clock
The frequency of this clock source must be
3.6864 MHz (electrical specification Parameter 1A) for
device communication at 9600 baud.
2.3.1.1
Crystal Oscillator / Ceramic
Resonators
A crystal or ceramic resonator can be connected to the
OSC1 and OSC2 pins to establish oscillation (refer to
Figure 2-1). The MCP2140A oscillator design requires
the use of a parallel-cut crystal. Use of a series cut
crystals may give a frequency outside of the crystal
manufacturers specifications.
FIGURE 2-1:
CRYSTAL OPERATION
(CERAMIC RESONATOR)
TABLE 2-1:
CAPACITOR SELECTION FOR
CERAMIC RESONATORS
TABLE 2-2:
CAPACITOR SELECTION FOR
CRYSTAL OSCILLATOR
Freq
OSC1 (C1)
OSC2 (C2)
3.6864 MHz
10 - 22 pF
Note:
Higher capacitance increases the stability
of the oscillator, but also increases the
start-up time. These values are for design
guidance only. Since each resonator has
its own characteristics, the user should
consult the resonator manufacturer for
appropriate
values
of
external
components.
Freq
OSC1 (C1)
OSC2 (C2)
3.6864 MHz
15 - 30 pF
Note:
Higher capacitance increases the stability
of the oscillator but also increases the
start-up time. These values are for design
guidance only. RS may be required to
avoid overdriving crystals with low drive
level specification. Since each crystal has
its own characteristics, the user should
consult the crystal manufacturer for
appropriate
values
of
external
components.
See Table 2-1 and Table 2-2 for recommended
values of C1 and C2.
Note:
A series resistor may be required for
AT strip cut crystals.
C1
C2
XTAL
OSC2
RS
OSC1
RF
To internal
MCP2140A
(Note)
logic
Ceramic
Resonator
相關PDF資料
PDF描述
V150A15C400BF2 CONVERTER MOD DC/DC 15V 400W
V150A15C400BF CONVERTER MOD DC/DC 15V 400W
MCP2515-E/SO IC CAN CONTROLLER W/SPI 18SOIC
PIC12LCE519-04I/P IC MCU OTP 1KX12 LV W/EE 8DIP
MCP2515-E/P IC CAN CONTROLLER W/SPI 18DIP
相關代理商/技術參數
參數描述
MCP2140DM-TMPSNS 功能描述:溫度傳感器開發工具 MCP2140 IrDA Wire- less Temp Demo RoHS:否 制造商:Texas Instruments 產品類型:Temperature Sensors and Control ICs 工具用于評估:MSP430G2553 接口類型:USB 工作電源電壓: 工作電源電流:
MCP2140-I/P 功能描述:網絡控制器與處理器 IC 9600bd fixd spd IrDA RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MCP2140-I/P 制造商:Microchip Technology Inc 功能描述:IrDA Protocol Handler Communication IC
MCP2140-I/SO 功能描述:網絡控制器與處理器 IC 9600bd fixd spd IrDA RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MCP2140-I/SO 制造商:Microchip Technology Inc 功能描述:IrDA Protocol Handler Communication IC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*