參數資料
型號： MCP2140AT-I/SS
廠商： Microchip Technology
文件頁數： 66/66頁
文件大小： 0K
描述： IC IRDA CONTROLLR DTE/DCE 20SSOP
標準包裝： 1,600
控制器類型： IRDA 標準協議?？刂破?br>
接口： UART
電源電壓： 2 V ~ 5.5 V
電流 - 電源： 2.2mA
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 20-SSOP（0.209"，5.30mm 寬）
供應商設備封裝： 20-SSOP
包裝： 帶卷 (TR)
配用： MCP2140DM-TMPSNS-ND - BOARD DEMO FOR MCP2140
其它名稱： MCP2140AT-I/SSTR
2007-2011 Microchip Technology Inc.
DS22050B-page 9
MCP2140A
2.4
Host UART Interface
The host UART interface communicates with the host
controller. This interface has eight signals associated
with it: TX, RX, RTS, CTS, DSR, DTR, CD and RI. Sev-
eral of these signals are locally generated (not passed
over the IR interface). The host UART is a full-duplex
interface, meaning that the system can transmit and
receive simultaneously.
2.4.1
BAUD RATE
The baud rate for the MCP2140A serial port (the TX
and RX pins) is fixed at 9600 baud when the device
frequency is 3.6864 MHz.
2.4.2
TRANSMITTING
When the host controller sends serial data to the
MCP2140A, the host controller’s baud rate is required
to match the baud rate of the MCP2140A’s serial port.
2.4.3
RECEIVING
When the host controller receives serial data from the
MCP2140A, the host controller’s baud rate is required
to match the baud rate of the MCP2140A’s serial port.
2.4.4
HARDWARE HANDSHAKING
There are three host UART signals used to control the
handshaking operation between the host controller and
the MCP2140A.
The following signals are host UART signals:
DSR
RTS
CTS
2.4.4.1
DSR
The DSR signal indicates that the MCP2140A has
established a link between the MCP2140A and the pri-
mary device. Please refer to Appendix B: “How
Devices Connect” for more information.
2.4.4.2
RTS
The RTS signal indicates to the MCP2140A that the
host controller is ready to receive serial data.
Once an IR packet with “data” has been received by the
MCP2140A, the RTS signal will need to be low for the
received data to be transferred to the host controller. If
the RTS signal remains high, an IR link timeout will
occur and the MCP2140A will disconnect from the pri-
mary device.
2.4.4.3
CTS
The CTS signal indicates that the MCP2140A UART
receive buffer is full. The MCP2140A generates the
CTS signal locally.
The MCP2140A UART receive buffer is 60 bytes and
the CTS signal will be driven high once 59 bytes have
been received.
After the MCP2140A UART has received a byte, there
is a latency before the CTS signal is driven high, if the
UART receive buffer has 59 bytes. The MCP2140A
then supports the reception of another byte (the 60th
byte). This allows a byte was being received when CTS
was driven high not to be lost. The MCP2140A UART
receive buffer supports 60 bytes, regardless if the last
byte started transmission before or after the CTS signal
was driven high.
The MCP2140A has a buffer for incoming data from the
IR host. This buffer supports the 60-byte data payload
plus the memory overhead of the packet. Another
60 byte buffer is provided to buffer data from the UART
serial port. The MCP2140A can handle IR data and
host UART serial port data simultaneously. A hardware
handshaking pin (CTS) is provided to inhibit the host
controller from sending serial data when the host UART
buffer is not available. Figure 2-3 shows CTS states
while Figure 2-4 shows an example of the CTS signal
when the host controller streams 250 bytes to the
MCP2140A. Figure 2-5 shows a flow chart for host
UART flow control using the CTS signal.
Note 1: The MCP2140A generates several non-
data signals locally.
2: The MCP2140A emulates a 3-wire serial
connection (TXD, RXD and GND). The
transceiver’s transmit data (TXD), receive
data (RXD) signals, and the state of the
CD. RI and DTR input pins are carried
back and forth to the primary device.
3: The RTS and CTS signals are local
emulations.
Note:
When the CTS output signal goes high, the
UART FIFO will store up to 1 additional
byte, for a maximum of 60 bytes.
相關PDF資料
PDF描述
V150A15C400BF2 CONVERTER MOD DC/DC 15V 400W
V150A15C400BF CONVERTER MOD DC/DC 15V 400W
MCP2515-E/SO IC CAN CONTROLLER W/SPI 18SOIC
PIC12LCE519-04I/P IC MCU OTP 1KX12 LV W/EE 8DIP
MCP2515-E/P IC CAN CONTROLLER W/SPI 18DIP
相關代理商/技術參數
參數描述
MCP2140DM-TMPSNS 功能描述:溫度傳感器開發工具 MCP2140 IrDA Wire- less Temp Demo RoHS:否 制造商:Texas Instruments 產品類型:Temperature Sensors and Control ICs 工具用于評估:MSP430G2553 接口類型:USB 工作電源電壓: 工作電源電流:
MCP2140-I/P 功能描述:網絡控制器與處理器 IC 9600bd fixd spd IrDA RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MCP2140-I/P 制造商:Microchip Technology Inc 功能描述:IrDA Protocol Handler Communication IC
MCP2140-I/SO 功能描述:網絡控制器與處理器 IC 9600bd fixd spd IrDA RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MCP2140-I/SO 制造商:Microchip Technology Inc 功能描述:IrDA Protocol Handler Communication IC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*