- 您現在的位置：買賣IC網 > PDF目錄16672 > MCP2140DM-TMPSNS (Microchip Technology)BOARD DEMO FOR MCP2140 PDF資料下載
參數資料
| 型號： | MCP2140DM-TMPSNS |
| 廠商： | Microchip Technology |
| 文件頁數： | 58/58頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD DEMO FOR MCP2140 |
| 產品培訓模塊： | PIC18 J Series MCU Overview |
| 標準包裝： | 1 |
| 主要目的： | 接口，IrDA |
| 嵌入式： | 是，MCU，8 位 |
| 已用 IC / 零件： | MCP2140 |
| 主要屬性： | 帶 PIC18F MCU 和溫度傳感器的 IrDA 控制器 |
| 次要屬性： | 設置為數據記錄器 |
| 已供物品： | 板，軟件 |
| 產品目錄頁面： | 685 (CN2011-ZH PDF) |
| 相關產品： | MCP2140A-I/SS-ND - IC IRDA CONTROLLR DTE/DCE 20SSOP MCP2140A-I/SO-ND - IC IRDA CONTROLLR DTE/DCE 18SOIC MCP2140A-I/P-ND - IC IRDA CONTROLLR DTE/DCE 18DIP MCP2140AT-I/SSTR-ND - IC IRDA CONTROLLR DTE/DCE 20SSOP MCP2140AT-I/SOTR-ND - IC IRDA CONTROLLR DTE/DCE 18SOIC MCP2140T-I/SS-ND - IC IRDA CONTROLLR DTE/DCE 20SSOP MCP2140T-I/SO-ND - IC IRDA CONTROLLR DTE/DCE 18SOIC MCP2140-I/SS-ND - IC IRDA CONTROLLR DTE/DCE 20SSOP MCP2140-I/SO-ND - IC IRDA CONTROLLR DTE/DCE 18SOIC MCP2140-I/P-ND - IC IRDA CONTROLLER DTE/DCE 18DIP |
| 其它名稱： | MCP2140DM-TMPSNSR MCP2140DM-TMPSNSR-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁當前第58頁
2003 Microchip Technology Inc.
Preliminary
DS21790A-page 9
MCP2140
2.4
Host UART Interface
The Host UART interface communicates with the Host
Controller. This interface has eight signals associated
with it: TX, RX, RTS, CTS, DSR, DTR, CD and RI. Sev-
eral of these signals are locally generated (not passed
over the IR interface). The Host UART is a half-duplex
interface, meaning that the system is either transmitting
or receiving, but not both simultaneously.
2.4.1
BAUD RATE
The baud rate for the MCP2140 serial port (the TX and
RX pins) is fixed at 9600 baud when the device
frequency is 7.3728 MHz.
2.4.2
TRANSMITTING
When the controller sends serial data to the MCP2140,
the controller’s baud rate is required to match the baud
rate of the MCP2140’s serial port.
2.4.3
RECEIVING
When the controller receives serial data from the
MCP2140, the controller’s baud rate is required to
match the baud rate of the MCP2140’s serial port.
2.4.4
HARDWARE HANDSHAKING
There are three Host UART signals used to control the
handshaking operation between the Host Controller
and the MCP2140. They are:
DSR
RTS
CTS
2.4.4.1
DSR
The DSR signal is used to indicate that a link has been
established between the MCP2140 and the Primary
Device. Please refer to Section 2.13, “How Devices
Connect”, for information on how devices connect.
2.4.4.2
RTS
The RTS signal indicates to the MCP2140 that the Host
Controller is ready to receive serial data. Once an IR
data packet has been received, the RTS signal will be
low for the received data to be transferred to the Host
Controller. If the RTS signal remains high, an IR link
timeout will occur and the MCP2140 will disconnect
from the Primary Device.
2.4.4.3
CTS
The MCP2140 generates the CTS signal locally due to
buffer limitations.
The MCP2140 uses a 64-byte buffer for incoming data
from the IR Host. Another 29-byte buffer is provided to
buffer data from the UART serial port. The MCP2140
can handle IR data and Host UART serial port data
simultaneously. A hardware handshaking pin (CTS) is
provided to inhibit the Host Controller from sending
serial data when the Host UART buffer is not available
(Figure 2-3). Figure 2-4 shows a flow chart for Host
UART flow control using the CTS signal.
FIGURE 2-3:
HOST UART CTS SIGNAL AND THE RECEIVE BUFFER
Note 1: The MCP2140 generates several non-
data signals locally.
2: The MCP2140 emulates a 3-wire serial
connection (TXD, RXD and GND). The
transceiver’s
Transmit
Data
(TXD),
Receive Data (RXD) signals, and the
state of the CD. RI and DTR input pins
are carried back and forth to the Primary
device.
3: The RTS and CTS signals are local
emulations.
Note:
When the CTS output signal goes high, the
UART FIFO will store up to 6 bytes. This is
to allow devices that have a slow response
time to a change on the CTS signal time to
stop sending additional data (such as a
modem).
CTS
Receive Buffer Empty
MCP2140 Can Receive Data Receive Buffer Has 22 Bytes,
Receive Buffer
Receive Buffer Empty
MCP2140 Can Receive Data
IR Data Packet Transmitted
Full (29 Bytes)
CTS Pin Driven High
IR Data Packet Starts Transmission
相關PDF資料 |
PDF描述 |
|---|---|
| H8MMS-5006M | DIP CABLE - HDM50S/AE50M/HDM50S |
| VE-B20-EW | CONVERTER MOD DC/DC 5V 100W |
| GCB10DHFT | CONN CARDEDGE 20POS .050" SMD |
| RMW-10/3-1200/ADH-0 | HEAT SHRINK TUBING |
| RNF-100-1/2-BK-STK | HEATSHRINK RNF-100 1/2"X4' BLK |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP2140-I/P | 功能描述:網絡控制器與處理器 IC 9600bd fixd spd IrDA RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| MCP2140-I/P | 制造商:Microchip Technology Inc 功能描述:IrDA Protocol Handler Communication IC |
| MCP2140-I/SO | 功能描述:網絡控制器與處理器 IC 9600bd fixd spd IrDA RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| MCP2140-I/SO | 制造商:Microchip Technology Inc 功能描述:IrDA Protocol Handler Communication IC |
| MCP2140-I/SS | 功能描述:網絡控制器與處理器 IC 9600bd fixd spd IrDA RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。