- 您現在的位置：買賣IC網 > PDF目錄16672 > MCP2140DM-TMPSNS (Microchip Technology)BOARD DEMO FOR MCP2140 PDF資料下載
參數資料
| 型號： | MCP2140DM-TMPSNS |
| 廠商： | Microchip Technology |
| 文件頁數： | 8/58頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD DEMO FOR MCP2140 |
| 產品培訓模塊： | PIC18 J Series MCU Overview |
| 標準包裝： | 1 |
| 主要目的： | 接口，IrDA |
| 嵌入式： | 是，MCU，8 位 |
| 已用 IC / 零件： | MCP2140 |
| 主要屬性： | 帶 PIC18F MCU 和溫度傳感器的 IrDA 控制器 |
| 次要屬性： | 設置為數據記錄器 |
| 已供物品： | 板，軟件 |
| 產品目錄頁面： | 685 (CN2011-ZH PDF) |
| 相關產品： | MCP2140A-I/SS-ND - IC IRDA CONTROLLR DTE/DCE 20SSOP MCP2140A-I/SO-ND - IC IRDA CONTROLLR DTE/DCE 18SOIC MCP2140A-I/P-ND - IC IRDA CONTROLLR DTE/DCE 18DIP MCP2140AT-I/SSTR-ND - IC IRDA CONTROLLR DTE/DCE 20SSOP MCP2140AT-I/SOTR-ND - IC IRDA CONTROLLR DTE/DCE 18SOIC MCP2140T-I/SS-ND - IC IRDA CONTROLLR DTE/DCE 20SSOP MCP2140T-I/SO-ND - IC IRDA CONTROLLR DTE/DCE 18SOIC MCP2140-I/SS-ND - IC IRDA CONTROLLR DTE/DCE 20SSOP MCP2140-I/SO-ND - IC IRDA CONTROLLR DTE/DCE 18SOIC MCP2140-I/P-ND - IC IRDA CONTROLLER DTE/DCE 18DIP |
| 其它名稱： | MCP2140DM-TMPSNSR MCP2140DM-TMPSNSR-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁
MCP2140
DS21790A-page 16
Preliminary
2003 Microchip Technology Inc.
2.10.1
IMPROVING THROUGHPUT
Actual maximum throughput is dependent on several
factors, including:
Characteristics of the Primary device
Characteristics of the MCP2140
IrDA standard protocol overhead
The IrDA standard specifies how the data is passed
between the Primary device and Secondary device. In
IrCOMM, an additional 8 bytes are used by the protocol
for each packet transfer.
The most significant factor in data throughput is how
well the data frames are filled. If only 1 byte is sent at a
time, the throughput overhead of the IrCOMM protocol
is 89% (see Table 2-5). The best way to maximize
throughput is to align the amounts of data with the
receive buffer (IR and Host UART) packet size of the
MCP2140.
Then there is the delay between when data packets
are sent and received. See Figure 2-10 for an example
of this delay (look at CTS signal falling edges). In this
screen capture, a Palm m105 is receiving a 240-
byte string of data from the MCP2140. When the CTS
signal goes high, the Host Controller stops sending
data (23 bytes per CTS low-time). The CTS falling
edge to CTS falling edge is approximately 90 ms (typ-
ical). This CTS high-time affects the total data through-
put. The CTS high-time will be dependant on the
characteristics of the Primary device.
TABLE 2-5:
IRCOMM OVERHEAD %
2.10.1.1
From the Primary Device
The MCP2140 uses a fixed IR Receiver data block size
of 64 bytes.
The minimum size frame the Primary device can
respond with is 6 bytes.
2.10.1.2
From the MCP2140
The MCP2140 uses a fixed Host UART Receiver data
block size of 29 bytes.
2.11
Turnaround Latency
An IR link can be compared to a one-wire data connec-
tion. The IR transceiver can transmit or receive, but not
both at the same time. A delay of one bit time is recom-
mended between the time a byte is received and
another byte is transmitted.
2.12
Device ID
The MCP2140 has a fixed Device ID. This Device ID is
“MCP2140 xx”, with the xx indicating the silicon
revision of the device.
MCP2140
Data
Packet
Size
(Bytes)
IrCOMM
Overhead
(Bytes)
IrCOMM
Overhead
% (1)
Comment
IR
Receive
64
8
11 %
1
8
89 %
Host
UART
Receive
29
8
22 %
23
8
26 %
1
8
89 %
Note 1: Overhead % =
Overhead/(Overhead + Data).
2: The maximum number of bytes of the IR
Receive buffer.
3: The maximum number of bytes of the
Host UART Receive buffer.
4: The CTS signal is driven high at 23 byte.
相關PDF資料 |
PDF描述 |
|---|---|
| H8MMS-5006M | DIP CABLE - HDM50S/AE50M/HDM50S |
| VE-B20-EW | CONVERTER MOD DC/DC 5V 100W |
| GCB10DHFT | CONN CARDEDGE 20POS .050" SMD |
| RMW-10/3-1200/ADH-0 | HEAT SHRINK TUBING |
| RNF-100-1/2-BK-STK | HEATSHRINK RNF-100 1/2"X4' BLK |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP2140-I/P | 功能描述:網絡控制器與處理器 IC 9600bd fixd spd IrDA RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| MCP2140-I/P | 制造商:Microchip Technology Inc 功能描述:IrDA Protocol Handler Communication IC |
| MCP2140-I/SO | 功能描述:網絡控制器與處理器 IC 9600bd fixd spd IrDA RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| MCP2140-I/SO | 制造商:Microchip Technology Inc 功能描述:IrDA Protocol Handler Communication IC |
| MCP2140-I/SS | 功能描述:網絡控制器與處理器 IC 9600bd fixd spd IrDA RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。