參數資料
型號： MCP2200T-I/SS
廠商： Microchip Technology
文件頁數： 23/34頁
文件大?。?/td> 0K
描述： IC USB 2.0 - UART 20SSOP
標準包裝： 1,600
特點： USB 至 UART
通道數： 8
FIFO's： 256 字節
規程： USB 2.0
電源電壓： 3 V ~ 5.5 V
帶自動流量控制功能： 是
安裝類型： 表面貼裝
封裝/外殼： 20-SSOP（0.209"，5.30mm 寬）
供應商設備封裝： 20-SSOP
包裝： 帶卷 (TR)
2010-2011 Microchip Technology Inc.
DS22230D-page 3
MCP2003/4/3A/4A
1.0
DEVICE OVERVIEW
The MCP2003/4/3A/4A devices provide a physical
interface between a microcontroller and a LIN bus.
These devices will translate the CMOS/TTL logic levels
to LIN logic level, and vice versa. It is intended for
automotive and industrial applications with serial bus
speeds up to 20 Kbaud.
LIN specification 2.1 requires that the transceiver of all
nodes in the system is connected via the LIN pin, refer-
enced to ground and with a maximum external
termination resistance load of 510
Ω from LIN bus to
battery supply. The 510
Ω corresponds to 1 master and
15 slave nodes.
The VREN pin can be used to drive the logic input of an
external voltage regulator. This pin is high in all modes
except for Power-Down mode.
1.1
External Protection
1.1.1
REVERSE BATTERY PROTECTION
An external reverse-battery-blocking diode should be
used to provide polarity protection (see Example 1-1).
1.1.2
TRANSIENT VOLTAGE
PROTECTION (LOAD DUMP)
An external 43V transient suppressor (TVS) diode,
between VBB and ground, with a 50
Ω transient
protection resistor (RTP) in series with the battery
supply and the VBB pin serve to protect the device from
power transients (see Example 1-1) and ESD events.
While this protection is optional, it is considered good
engineering practice.
1.2
Internal Protection
1.2.1
ESD PROTECTION
For component-level ESD ratings, please refer to the
maximum operation specifications.
1.2.2
GROUND LOSS PROTECTION
The LIN Bus specification states that the LIN pin must
transition to the recessive state when ground is
disconnected. Therefore, a loss of ground effectively
forces the LIN line to a high-impedance level.
1.2.3
THERMAL PROTECTION
The thermal protection circuit monitors the die
temperature and is able to shut down the LIN
transmitter.
There are two causes for a thermal overload. A thermal
shut down can be triggered by either, or both, of the
following thermal overload conditions.
LIN bus output overload
Increase in die temperature due to increase in
environment temperature
Driving the TXD and checking the RXD pin makes it
possible to determine whether there is a bus contention
(Rx = low, Tx = high) or a thermal overload condition
(Rx = high, Tx = low). After a thermal overload event,
the device will automatically recover once the die
temperature has fallen below the recovery temperature
threshold. See Figure 1-1.
FIGURE 1-1:
THERMAL SHUTDOWN
STATE DIAGRAM
Operation
Mode
Transmitter
Shutdown
LIN bus
Shorted
to VBB
Temp < SHUTDOWN
TEMP
相關PDF資料
PDF描述
MAX3111ECNI+G36 IC UART SPI COMPAT 28-DIP
MAX3110ECNI+G36 IC TXRX RS232 SPI W/CAP 28-DIP
ATMEGA164PA-MCHR MCU AVR 16KB FLASH 20MHZ 44-VQFN
SC16C654BIBS,551 IC UART QUAD W/FIFO 48-HVQFN
SC16C654BIBS,528 IC QUAD UART 64BYTE 48HVQFN
相關代理商/技術參數
參數描述
MCP-220-51202-0N 制造商:SUPER MICRO COMPUTER, INC. 功能描述:DVD KIT - Bulk
MCP-220-73201-0N 制造商:Supermicro Computer Inc 功能描述:SC732 2.5INCH HDD CAGE - Bulk
MCP-220-81502-0N 制造商:Supermicro Computer Inc 功能描述:Slim SATA DVD Kit 制造商:Supermicro Computer Inc 功能描述:SLIM SATA DVD KIT - Bulk 制造商:Supermicro Computer 功能描述: 制造商:Supermicro Computer 功能描述:Slim SATA DVD Kit
MCP-220-81601-0N 制造商:SUPER MICRO COMPUTER, INC. 功能描述:SUPERMICRO 2.5-IN HDD BKT - Bulk
MCP-220-82504-0B 制造商:SUPER MICRO COMPUTER, INC. 功能描述:SUPERMICRO PART - Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*