參數資料
型號: MCP4018T-503E/LT
廠商: Microchip Technology
文件頁數: 38/51頁
文件大小: 0K
描述: IC DGTL POT 50K 128TAPS SC70-6
標準包裝: 1
接片: 128
電阻(歐姆): 50k
電路數: 1
溫度系數: 標準值 150 ppm/°C
存儲器類型: 易失
接口: I²C
電源電壓: 1.8 V ~ 5.5 V
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 6-TSSOP,SC-88,SOT-363
供應商設備封裝: SC-70-6
包裝: 標準包裝
產品目錄頁面: 674 (CN2011-ZH PDF)
其它名稱: MCP4018T-503E/LTDKR
2009 Microchip Technology Inc.
DS22147A-page 43
MCP4017/18/19
6.2
Resistor Configurations
6.2.1
RHEOSTAT CONFIGURATION
When used as a rheostat, two of the three digital
potentiometer’s terminals are used as a resistive
element in the circuit. With terminal W (wiper) and
either terminal A or terminal B, a variable resistor is
created. The resistance will depend on the tap setting
of the wiper (and the wiper’s resistance). The
resistance is controlled by changing the wiper setting
The unused terminal (B or A) should be left floating.
Figure 6-2 shows the two possible resistors that can be
used. Reversing the polarity of the A and B terminals
will not affect operation.
FIGURE 6-2:
Rheostat Configuration.
This allows the control of the total resistance between
the two nodes. The total resistance depends on the
“starting” terminal to the Wiper terminal. So at the code
00h, the RBW resistance is minimal (RW), but the RAW
resistance in maximized (RAB + RW). Conversely, at the
code 3Fh, the RAW resistance is minimal (RW), but the
RBW resistance in maximized (RAB + RW).
The resistance Step size (RS) equates to one LSb of
the resistor.
The pinout for the rheostat devices is such that as the
wiper register is incremented, the resistance of the
resistor will increase (as measured from Terminal B to
the W Terminal).
6.2.2
POTENTIOMETER
CONFIGURATION
When used as a potentiometer, all three terminals of
the device are tied to different nodes in the circuit. This
allows the potentiometer to output a voltage
proportional to the input voltage. This configuration is
sometimes
called
voltage
divider
mode.
The
potentiometer is used to provide a variable voltage by
adjusting the wiper position between the two endpoints
as shown in Figure 6-3. Reversing the polarity of the A
and B terminals will not affect operation.
FIGURE 6-3:
Potentiometer
Configuration.
The temperature coefficient of the RAB resistors is
minimal by design. In this configuration, the resistors all
change uniformly, so minimal variation should be seen.
The Wiper resistor temperature coefficient is different
to the RAB temperature coefficient. The voltage at node
V3 (Figure 6-3) is not dependent on this Wiper
resistance, just the ratio of the RAB resistors, so this
temperature coefficient in most cases can be ignored.
Note:
To avoid damage to the internal wiper
circuitry in this configuration, care should
be taken to insure the current flow never
exceeds 2.5 mA.
A
B
W
Resistor
RAW
RBW
or
Note:
To avoid damage to the internal wiper
circuitry in this configuration, care should
be taken to insure the current flow never
exceeds 2.5 mA.
A
B
W
V1
V3
V2
相關PDF資料
PDF描述
VI-23H-MW CONVERTER MOD DC/DC 52V 100W
DS1743-100+ IC RTC RAM Y2K 5V 100NS 28-EDIP
VI-23F-MX-B1 CONVERTER MOD DC/DC 72V 75W
VI-23F-MW CONVERTER MOD DC/DC 72V 100W
VI-23D-MX-B1 CONVERTER MOD DC/DC 85V 75W
相關代理商/技術參數
參數描述
MCP4019 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:7-Bit Single I2C? Digital POT with Volatile Memory in SC70
MCP4019-103E/LT 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:7-Bit Single I2C? Digital POT with Volatile Memory in SC70
MCP4019-104E/LT 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:7-Bit Single I2C? Digital POT with Volatile Memory in SC70
MCP4019-502E/LT 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:7-Bit Single I2C? Digital POT with Volatile Memory in SC70
MCP4019-503E/LT 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:7-Bit Single I2C? Digital POT with Volatile Memory in SC70