參數資料
型號: MCP4706A0T-E/CH
廠商: Microchip Technology
文件頁數: 32/86頁
文件大小: 0K
描述: IC DAC 8BIT NV EEP I2C SOT-23-6
標準包裝: 1
設置時間: 6µs
位數: 8
數據接口: EEPROM,I²C,串行
轉換器數目: 1
電壓電源: 單電源
功率耗散(最大): 452mW
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: SOT-23-6
供應商設備封裝: SOT-23-6
包裝: 標準包裝
輸出數目和類型: 1 電壓,單極
采樣率(每秒): *
其它名稱: MCP4706A0T-E/CHDKR
MCP4706/4716/4726
DS22272C-page 38
2011-2012 Microchip Technology Inc.
4.4.3
OUTPUT SLEW RATE
Figure 4-5 shows an example of the slew rate of the
VOUT pin. The slew rate can be affected by the
characteristics of the circuit connected to the VOUT pin.
FIGURE 4-5:
VOUT pin Slew Rate.
4.4.4
SMALL CAPACITIVE LOAD
With a small capacitive load, the output buffer’s current
is not affected by the capacitive load (CL). However, the
VOUT pin’s voltage is not a step transition from one
output value (wiper code value) to the next output
value. The change of the VOUT voltage is limited by the
output buffer’s characteristics, so the VOUT pin voltage
will have a slope from the old voltage to the new
voltage. This slope is fixed for the output buffer, and is
referred to as the buffer slew rate (SRBUF).
4.4.5
LARGE CAPACITIVE LOAD
With a larger capacitive load, the slew rate is deter-
mined by two factors:
The output buffer’s short circuit current (ISC)
The VOUT pin’s external load
IOUT cannot exceed the output buffer’s short circuit
current (ISC) which fixes the output buffer slew rate
(SRBUF). The voltage on the capacitive load (CL), VCL,
changes at a rate proportional to IOUT, which fixes a
capacitive load slew rate (SRCL).
So the VCL voltage slew rate is limited to the slower of
the output buffer’s internally set slew rate (SRBUF) and
the capacitive load slew rate (SRCL).
4.4.6
DRIVING RESISTIVE AND
CAPACITIVE LOADS
The VOUT pin can drive up to 100 pF of capacitive load
in parallel with a 5 k
Ω resistive load (to meet electrical
specifications). Figure 2-94 shows the VOUT vs.
Resistive Load.
VOUT drops slowly as the load resistance decreases
after about 3.5 k
Ω. It is recommended to use a load
with RL greater than 5 kΩ.
Driving large capacitive loads can cause stability
problems for voltage feedback op amps. As the load
capacitance increases, the feedback loop’s phase
margin decreases and the closed-loop bandwidth is
reduced. This produces gain peaking in the frequency
response with overshoot and ringing in the step
response. That is, since the VOUT pin’s voltage does
not quickly follow the buffer’s input voltage (due to the
large capacitive load), the output buffer will overshoot
the desired target voltage. Once the driver detects this
overshoot, it compensates by forcing it to a voltage
below the target. This causes voltage ringing on the
VOUT pin.
So, when driving large capacitive loads with the output
buffer, a small series resistor (RISO) at the output (see
Figure 4-6) improves the output buffer’s stability
(feedback loop’s phase margin) by making the output
load resistive at higher frequencies. The bandwidth will
be generally lower than the bandwidth with no
capacitive load.
FIGURE 4-6:
Circuit to Stabilize Output
Buffer for Large Capacitive Loads (CL).
The RISO resistor value for your circuit needs to be
selected. The resulting frequency response peaking
and step response overshoot for this RISO resistor
value should be verified on the bench. Modify the
RISO’s resistance value until the output characteristics
meet your requirements.
A method to evaluate the system’s performance is to
inject a step voltage on the VREF pin and observe the
VOUT pin’s characteristics.
Time
Slew Rate =
Wiper = A
V
OUT
VOUT(A)
VOUT(B)
Wiper = B
| VOUT(B) - VOUT(A) |
ΔT
Note:
Additional insight into circuit design for
driving capacitive loads can be found in
AN884 “Driving Capacitive Loads With Op
Amps” (DS00884).
VOUT
Op
Amp
VW
CL
RISO
RL
VCL
相關PDF資料
PDF描述
VI-BT4-MY-F2 CONVERTER MOD DC/DC 48V 50W
VE-22P-MW-F3 CONVERTER MOD DC/DC 13.8V 100W
M83723/74W22326 CONN RCPT 32POS JAM NUT W/PINS
MK3732-10SLFTR IC VCXO/MULTIPLIER 16-SOIC
VI-BT3-MY-F3 CONVERTER MOD DC/DC 24V 50W
相關代理商/技術參數
參數描述
MCP4706A1T-E/CH 功能描述:數模轉換器- DAC Sngl 8B NV DAC w/Ext Vref & I2C interface RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
MCP4706A1T-E/MAY 功能描述:數模轉換器- DAC Sngl 8B NV DAC w/Ext Vref & I2C interface RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
MCP4706A2T-E/CH 功能描述:數模轉換器- DAC Sngl 8B NV DAC w/Ext Vref & I2C interface RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
MCP4706A2T-E/MAY 功能描述:數模轉換器- DAC Sngl 8B NV DAC w/Ext Vref & I2C interface RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
MCP4706A3T-E/CH 功能描述:數模轉換器- DAC Sngl 8B NV DAC w/Ext Vref & I2C interface RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube