參數資料
型號： MCP601-E/ST
廠商： Microchip Technology
文件頁數： 7/34頁
文件大?。?/td> 0K
描述： IC OPAMP SNGL 2.7V 8TSSOP
標準包裝： 100
放大器類型： 通用
電路數： 1
輸出類型： 滿擺幅
轉換速率： 2.3 V/µs
增益帶寬積： 2.8MHz
電流 - 輸入偏壓： 1pA
電壓 - 輸入偏移： 700µV
電流 - 電源： 230µA
電流 - 輸出 / 通道： 22mA
電壓 - 電源，單路/雙路(±)： 2.7 V ~ 6 V
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 8-TSSOP（0.173"，4.40mm 寬）
供應商設備封裝： 8-TSSOP
包裝： 管件
2007 Microchip Technology Inc.
DS21314G-page 15
MCP601/1R/2/3/4
4.8.2
INSTRUMENTATION AMPLIFIER
CIRCUITS
Instrumentation amplifiers have a differential input that
subtracts one input voltage from another and rejects
common mode signals. These amplifiers also provide a
single-ended output voltage.
The three-op amp instrumentation amplifier is illustrated
in Figure 4-10. One advantage of this approach is unity-
gain operation, while one disadvantage is that the
common mode input range is reduced as R2/RG gets
larger.
FIGURE 4-10:
Three-Op Amp
Instrumentation Amplifier.
The two-op amp instrumentation amplifier is shown in
Figure 4-11. While its power consumption is lower than
the three-op amp version, its main drawbacks are that
the common mode range is reduced with higher gains
and it must be configured in gains of two or higher.
FIGURE 4-11:
Two-Op Amp
Instrumentation Amplifier.
Both instrumentation amplifiers should use a bulk
bypass capacitor of at least 1 F. The CMRR of these
amplifiers will be set by both the op amp CMRR and
resistor matching.
4.8.3
PHOTO DETECTION
The MCP601/1R/2/3/4 op amps can be used to easily
convert the signal from a sensor that produces an
output current (such as a photo diode) into a voltage (a
transimpedance amplifier). This is implemented with a
single resistor (R2) in the feedback loop of the
amplifiers shown in Figure 4-12 and Figure 4-13. The
optional capacitor (C2) sometimes provides stability for
these circuits.
A photodiode configured in the Photovoltaic mode has
zero voltage potential placed across it (Figure 4-12). In
this mode, the light sensitivity and linearity is
maximized, making it best suited for precision
applications. The key amplifier specifications for this
application are: low input bias current, low noise,
common mode input voltage range (including ground),
and rail-to-rail output.
FIGURE 4-12:
Photovoltaic Mode Detector.
In contrast, a photodiode that is configured in the
Photoconductive mode has a reverse bias voltage
across the photo-sensing element (Figure 4-13). This
decreases the diode capacitance, which facilitates
high-speed
operation
(e.g.,
high-speed
digital
communications). The design trade-off is increased
diode leakage current and linearity errors. The op amp
needs to have a wide Gain Bandwidth Product
(GBWP).
FIGURE 4-13:
Photoconductive Mode
Detector.
MCP60X
V1
MCP60X
V2
R2
R3
MCP60X
R4
R3
R4
VOUT
VREF
RG
+
–
+
–
+
V
OUT
V
1
V
2
–
() 1
2R
2
R
G
---------
+
R4
R
3
------
V
REF
+
=
MCP60X
V2
RG
R2
MCP60X
R1
VOUT
VREF
V1
R1
-
+
-
+
V
OUT
V
1
V
2
–
() 1
R
1
R
2
------
2R
1
R
G
---------
++
V
REF
+
=
D1
Light
VOUT
VDD
MCP60X
R2
C2
ID1
VOUT = ID1 R2
–
+
D1
Light
VOUT
VDD
MCP60X
R2
C2
ID1
VOUT = ID1 R2
VBIAS
VBIAS < 0V
–
+
相關PDF資料
PDF描述
LRC-LRF1206LF-01-R020-F RES .020 OHM 0.5W 1% 1206 SMD
MCP6G01-E/SN IC GAIN BLOCK 1.8V 1CH 8SOIC
TSM-107-01-T-DV CONN HEADER 14POS .100" DBL SMD
MCP6281RT-E/OT IC OPAMP 2.2V SNGL R-R SOT23-5
IPBT-102-H1-T-S PWR MATE TERM STRIP HDR 2POS
相關代理商/技術參數
參數描述
MCP601-I 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:2.7V to 5.5V Single Supply CMOS Op Amps
MCP601-I/CH 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:2.7V to 5.5V Single-Supply CMOS Op Amps
MCP601-I/OT 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:2.7V to 5.5V Single-Supply CMOS Op Amps
MCP601-I/P 功能描述:運算放大器 - 運放 Single 2.7V RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel
MCP601-I/P 制造商:Microchip Technology Inc 功能描述:IC OP AMP CMOS RRO/P DIP8 601
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*