參數資料
型號: MCP6444-E/SL
廠商: Microchip Technology
文件頁數: 7/46頁
文件大?。?/td> 0K
描述: IC OPAMP QUAD 1.6V 9KHZ 14SOIC
標準包裝: 57
放大器類型: 通用
電路數: 4
輸出類型: 滿擺幅
轉換速率: 0.003 V/µs
增益帶寬積: 9kHz
電流 - 輸入偏壓: 1pA
電壓 - 輸入偏移: 4500µV
電流 - 電源: 0.45µA
電流 - 輸出 / 通道: 22mA
電壓 - 電源,單路/雙路(±): 1.4 V ~ 6 V
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 14-SOIC(0.154",3.90mm 寬)
供應商設備封裝: 14-SOICN
包裝: 管件
2010-2012 Microchip Technology Inc.
DS22257C-page 15
MCP6441/2/4
The easiest way to reduce surface leakage is to use a
guard ring around sensitive pins (or traces). The guard
ring is biased at the same voltage as the sensitive pin.
An example of this type of layout is shown in
FIGURE 4-6:
Example Guard Ring Layout
for Inverting Gain.
1.
Non-inverting Gain and Unity-Gain Buffer:
a)
Connect the non-inverting pin (VIN+) to the
input with a wire that does not touch the
PCB surface.
b)
Connect the guard ring to the inverting input
pin (VIN–). This biases the guard ring to the
Common Mode input voltage.
2.
Inverting
Gain
and
Transimpedance
Gain
Amplifiers (convert current to voltage, such as
photo detectors):
a)
Connect the guard ring to the non-inverting
input pin (VIN+). This biases the guard ring
to the same reference voltage as the op
amp (e.g., VDD/2 or ground).
b)
Connect the inverting pin (VIN–) to the input
with a wire that does not touch the PCB
surface.
4.6
Application Circuits
4.6.1
BATTERY CURRENT SENSING
The MCP6441/2/4 op amp’s Common Mode Input
Range, which goes 0.3V beyond both supply rails,
supports their use in high-side and low-side battery
current sensing applications. The low quiescent current
(450 nA, typical) helps prolong battery life, and the
rail-to-rail output supports detection of low currents.
Figure 4-7 shows a high side battery current sensor
circuit. The 10
Ω resistor is sized to minimize power
losses. The battery current (IDD) through the 10Ω
resistor causes its top terminal to be more negative
than the bottom terminal. This keeps the Common
Mode input voltage of the op amp below VDD, which is
within its allowed range. The output of the op amp will
also be below VDD, within its Maximum Output Voltage
Swing specification.
FIGURE 4-7:
Battery Current Sensing.
Guard Ring
VIN–VIN+
VSS
VDD
IDD
100 k
Ω
1M
Ω
1.4V
VOUT
10
Ω
to
6.0V
I
DD
V
DD
V
OUT
10 V/V
() 10
Ω
()
------------------------------------------
=
To load
MCP6441
相關PDF資料
PDF描述
MCP6V28-E/MS IC OPAMP AUTO-ZERO SGL 8MSOP
SMBJ78CAHE3/5B TVS BIDIR 600W 78V 5% SMB
MCP6V28-E/SN IC OPAMP AUTO-ZERO SGL 8SOIC
SMBJ75CAHE3/5B TVS BIDIR 600W 75V 5% SMB
9-146257-0-32 CONN HEADR BRKWAY .100 64POS STR
相關代理商/技術參數
參數描述
MCP6444T-E/SL 功能描述:運算放大器 - 運放 450 nA, 9 kHz Op Amp RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比(最小值):63 dB 輸入補償電壓:1 mV 輸入偏流(最大值):10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel
MCP6444T-E/ST 功能描述:運算放大器 - 運放 450 nA, 9 kHz Op Amp RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比(最小值):63 dB 輸入補償電壓:1 mV 輸入偏流(最大值):10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel
MCP6471T-E/LTY 制造商:Microchip Technology Inc 功能描述:SINGLE 2 MHZ OP, E TEMP - Tape and Reel 制造商:Microchip Technology Inc 功能描述:IC OPAMP GP RRIO 2MHZ SC70-5 制造商:Microchip Technology Inc 功能描述:Single 2 MHz OP E temp
MCP6471T-E/OT 功能描述:運算放大器 - 運放 16bit deltasigma ADC dual channel 15sps RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比(最小值):63 dB 輸入補償電壓:1 mV 輸入偏流(最大值):10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel
MCP6472-E/MS 制造商:Microchip Technology Inc 功能描述:OP-AMP 2MHz 1.1V/ 1.5mV 制造商:Microchip Technology Inc 功能描述:OP-AMP 2MHz 1.1V/ 1.5mV MSOP-8 制造商:Microchip Technology Inc 功能描述:OP-AMP, 2MHz, 1.1V/s, 1.5mV, MSOP-8